Alternatives and similar repositories for CycloidalDesign:

Users that are interested in CycloidalDesign are comparing it to the libraries listed below

• Neumi / tmc2209_devboard
  An Arduino shield to test the TMC2209 stepper motion controller by Trinamic.
  ☆36Updated last year
• makerbase-motor / MKS-SERVO57D
  Makerbase MKS SERVO57D NEMA23 closed loop stepper motor Driver FOC quiet and efficient RS485 / CAN
  ☆50Updated 5 months ago
• Tomato1107 / Cycloidal-Drive-Animation
  Based on matplotlib
  ☆61Updated last year
• roTechnic / EccentricCycloidalGears
  ☆28Updated 3 years ago
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆34Updated last year
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆75Updated this week
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated last month
• uStepper / uStepperS
  ☆54Updated last year
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆41Updated 3 weeks ago
• DerAndere1 / Marlin
  Optimized firmware for RepRap 3D printers based on the Arduino platform. The branch Marlin2ForPipetBot is optimized firmware for cartesia…
  ☆54Updated 2 weeks ago
• gouldpa / Triple-Cycloidal-Robot-Arm-Proto-2
  ☆21Updated 5 years ago
• qwertpas / O32controller
  Miniature closed-loop controller for brushless DC motors
  ☆28Updated 8 months ago
• G-EDM / G-EDM-v1-deprecated
  The G-EDM is a 4in1 electrical discharge machine that supports sinker EDM, EDM engraving, EDM drilling and Wire EDM operations. In the fu…
  ☆49Updated last week
• benbreen / Cycloidal
  Cycloidal Gear Generator for Fusion 360
  ☆24Updated 8 years ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆106Updated 3 years ago
• KoshiroRobot / Simple-Smart-Servo-Driver
  ☆35Updated 4 months ago
• byDagor / Janus-Controller
  The Janus Controller is a Brushless motor driver with an on-board magnetic encoder, a three-phase MOSFET driver, three MOSFET half-bridge…
  ☆123Updated 4 years ago
• Arctos-Robotics / Arctos-grbl-v0.1
  6 Axis version of Grbl, the open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that …
  ☆52Updated 10 months ago
• buildbotics / bbctrl-firmware
  Buildbotics CNC Controller Firmware
  ☆69Updated 2 months ago
• PCrnjak / S-Drive-Firmware
  S_Drive is small bldc driver based on L6234 Three phase motor driver.
  ☆43Updated last year
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆47Updated last month
• roTechnic / internalECGears
  ☆22Updated 3 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆113Updated last year
• XRobots / RemoteDSM
  ☆58Updated 2 years ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆31Updated 6 months ago
• grblHAL / drivers
  Driver overview
  ☆34Updated last month
• MarginallyClever / sixi
  Sixi Robot Arm
  ☆23Updated 5 years ago
• Igitigit2 / SimpleCanLib
  CAN bus library for ESP32 and STM32 G431
  ☆28Updated 10 months ago
• RinthLabs / MaxFeeder
  Arduino Mega shield for controlling part feeders for Open PNP
  ☆29Updated 2 months ago