iplayfast / CycloidGearBox

Related projects: ⓘ

• janelia-arduino / TMC429
  The Trinamic TMC429 is a triple-axis dedicated step and direction motion controller for both position and velocity control with accelerat…
  ☆36Updated 5 months ago
• dsuarezv / GearSolver
  A cycloid gear graphical calculator to design cycloidal drives.
  ☆101Updated 2 years ago
• IdeaPropulsionSystems / CoolEpicyclicGearing
  Some resources for designing a special high-ratio planetary gearing system.
  ☆24Updated 5 years ago
• uStepper / uStepperS
  ☆54Updated 11 months ago
• roTechnic / CycloidalDesign
  ☆18Updated 2 years ago
• Seeed-Studio / Seeed_Arduino_AS5600
  The library comes with AS5600. Through this library, we can realize read the angles 、get magnetic from a magnet underneath the sensor.
  ☆105Updated 6 months ago
• grblHAL / Simulator
  grblHAL drivers for simulation (Linux and Windows)
  ☆25Updated 2 weeks ago
• Tomato1107 / Cycloidal-Drive-Animation
  Based on matplotlib
  ☆54Updated last year
• MarginallyClever / sixi
  Sixi Robot Arm
  ☆22Updated 5 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆73Updated 3 years ago
• benbreen / Cycloidal
  Cycloidal Gear Generator for Fusion 360
  ☆22Updated 8 years ago
• opengalvo / OPAL
  Minimalistic FW for Processing GCode to Galvanometer signals
  ☆66Updated 2 years ago
• kingoflolz / linear-actuator-hardware
  ☆54Updated 2 years ago
• G-EDM / G-EDM-v1-deprecated
  The G-EDM is a 4in1 electrical discharge machine that supports sinker EDM, EDM engraving, EDM drilling and Wire EDM operations. In the fu…
  ☆41Updated 3 weeks ago
• byDagor / Janus-Controller
  The Janus Controller is a Brushless motor driver with an on-board magnetic encoder, a three-phase MOSFET driver, three MOSFET half-bridge…
  ☆114Updated 3 years ago
• bdring / fluidterm
  A Serial Terminal for FluidNC
  ☆19Updated 2 years ago
• pedromneto97 / AccelStepper-MicroPython
  AccelStepper Library for Micropyton - ESP32
  ☆36Updated 5 years ago
• Aus3D / MagneticEncoder
  ☆16Updated 7 years ago
• mikedh / cycloidal
  Generate profiles for cycloidal drives, a mechanical reducer
  ☆21Updated 3 years ago
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆92Updated 2 years ago
• DerAndere1 / Marlin
  Optimized firmware for RepRap 3D printers based on the Arduino platform. The branch Marlin2ForPipetBot is optimized firmware for cartesia…
  ☆52Updated 2 weeks ago
• jared-hughes / grbl-scara
  Modification of grbl that computes motor steps based on a SCARA coordinate system. Grbl is open source, embedded, high performance g-code…
  ☆16Updated 3 years ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 7 years ago
• MakerLabTunisia / CARVER_X5
  CARVER X5 is an OpenSourceHarware 5 Axis CNC Carving Machine - by MakerLabTunisia
  ☆80Updated 3 years ago
• MarginallyClever / sixi-2
  Sixi 2 Robot Arm
  ☆34Updated 2 years ago
• kentavv / haimer_probe
  Automate LinuxCNC with machine vision by detecting and probing holes while reading the dial of a Haimer 3D Sensor
  ☆23Updated 4 years ago
• grblHAL / drivers
  Driver overview
  ☆27Updated 7 months ago
• Igitigit2 / SimpleCanLib
  CAN bus library for ESP32 and STM32 G431
  ☆21Updated 3 months ago
• MitchBradley / ESP3D-WEBUI
  A Web UI for ESP8266 or ESP32 based boards connected to 3D printers / CNC
  ☆30Updated 2 weeks ago
• buildbotics / bbctrl-pcb
  Buildbotics CNC, 3D printer and other machine controller
  ☆47Updated 2 years ago