Alternatives and similar repositories for LinuxCNC-RIO

Users that are interested in LinuxCNC-RIO are comparing it to the libraries listed below

• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆77Updated 3 months ago
• multigcs / riocore
  riocore
  ☆67Updated this week
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆33Updated last year
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆96Updated 7 months ago
• freakontrol / stmbl
  ☆37Updated 6 months ago
• mhouse1 / mechsoftronic
  FPGA based CNC Machine
  ☆95Updated 6 years ago
• wezhunter / ESP32_LinuxCNC_MotionController_RealTime
  ESP32 hardware based real-time LinuxCNC motion controller
  ☆52Updated last year
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆166Updated last week
• fdarling / mesa-smartserial-device-template
  Mesa SmartSerial (SSLBP) custom device template project
  ☆13Updated 5 years ago
• linuxcnc-ethercat / linuxcnc-ethercat
  LinuxCNC EtherCAT HAL driver
  ☆70Updated last month
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 5 years ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆30Updated last month
• MetalMusings / MyOwnEtherCATDevice
  Documentation accompanying the "Make My Own EtherCAT device" video serie on Youtube.
  ☆82Updated 3 months ago
• Deotti-cl / linuxcnc-esp32
  External pulse generator
  ☆17Updated 4 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆40Updated 5 months ago
• scottalford75 / LinuxCNC-3D-Printing
  ☆28Updated 6 months ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆161Updated 2 months ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆41Updated last year
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆64Updated 2 years ago
• photonfirmware / photon
  Open-Source firmware for pick and place feeders
  ☆70Updated 3 weeks ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆127Updated last month
• scottalford75 / Remora-RP2040-W5500
  Remora firmware for RP2040 with W5500 Ethernet
  ☆14Updated last year
• Peter-van-Tol / LITEXCNC-HUB75HAT
  A PCB that turns the Colorlight 5A-75B into an easy to use LinuxCNC motion controller
  ☆14Updated 2 years ago
• opengalvo / OPAL
  Minimalistic FW for Processing GCode to Galvanometer signals
  ☆102Updated last year
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆62Updated last month
• realthunder / fcad_pcb
  FreeCAD scripts for PCB CAD/CAM
  ☆152Updated last year
• machinekit / mksocfpga
  Hostmot2 FPGA code for SoC/FPGA platforms from Altera and Xilinx
  ☆32Updated 2 years ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 11 months ago
• sleepybishop / mojo_hostmot2
  hostmot2 firmware for the embedded micro mojo v3 fpga
  ☆11Updated 5 years ago
• scottalford75 / Remora-NVEM
  Remora firmware for Novusun NVEM controller board
  ☆16Updated last year