Alternatives and similar repositories for mechsoftronic:

Users that are interested in mechsoftronic are comparing it to the libraries listed below

• hzeller / beagleg
  G-code interpreter and stepmotor controller for crazy fast coordinated moves of up to 8 steppers. Uses the Programmable Realtime Unit (PR…
  ☆124Updated last year
• machinekit / mksocfpga
  Hostmot2 FPGA code for SoC/FPGA platforms from Altera and Xilinx
  ☆31Updated last year
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆77Updated 7 months ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆64Updated 3 weeks ago
• openpnp / openpnp-openbuilds
  An OpenPnP compatible SMT pick and place machine based on OpenBuilds linear motion components.
  ☆218Updated 7 years ago
• tinkercnc / spi-fpga-driver
  LinuxCNC to fpga-over-spi driver
  ☆25Updated 8 years ago
• madcowswe / Servo
  High performance motor control
  ☆89Updated 8 years ago
• BETZtechnik / ICEpick--Direct-drive-pick-and-place-head
  Pick and Place head with dual nozzles
  ☆39Updated 5 years ago
• issus / NEMA8-Juki-Tool-Changer
  Pick and Place tool changer nozzle to hold Juki 500 series nozzles on a NEMA8 hollow shaft motor
  ☆28Updated 8 years ago
• clementleger / Smoothieware-STM32
  [DEPRECATED] Modular, opensource, high performance G-code interpreter and CNC controller written in Object-Oriented C++
  ☆38Updated 9 years ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated 3 weeks ago
• Smoothieware / Smoothieboard
  ☆174Updated 6 years ago
• ottoragam / Tarocco
  Closed Loop Motor Controller
  ☆133Updated 4 years ago
• madcowswe / ODriveFPGA
  High performance motor control
  ☆101Updated 8 years ago
• multigcs / riocore
  riocore
  ☆39Updated this week
• verser-git / probe_screen
  Probe Screen for LinuxCNC
  ☆21Updated 6 years ago
• bdring / PSoC_Grbl
  PSoc5 Port of Grbl CNC Controller
  ☆36Updated 8 years ago
• cinderblock / 3-Phase-Driver
  Hardware design for a 3 Phase BLDC controller
  ☆57Updated 5 years ago
• Smoothieware / Smoothieboard2
  Hardware files for the Smoothieboard v2, and extension boards
  ☆57Updated 10 months ago
• ErichStyger / McuOpenPnP_Machine
  Repository for the McuOnEclipse OpenPnP machine
  ☆64Updated 4 years ago
• cdsteinkuehler / bobc_hardware
  CRAMPS - A Cape version of the RAMPS-FD design for 3D printing
  ☆45Updated 6 years ago
• gkyle / xaar128
  ☆50Updated 6 years ago
• KurtJacobson / hazzy
  Touchscreen UI for LinuxCNC
  ☆33Updated 5 years ago
• cinderblock / 3-Phase-Controller
  Firmware for 3 Phase BLDC controller
  ☆41Updated 4 years ago
• langwadt / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆33Updated 3 years ago
• easyw / kicad-3d-models-in-freecad
  kicad 3d models in freecad
  ☆140Updated 9 months ago
• cnc-club / linuxcnc-features
  LinuxCNC Features
  ☆57Updated 9 years ago
• kinsamanka / PICnc-V2
  PICnc V2 is a PIC32 based hardware step generator board that is designed for MachineKit
  ☆28Updated 9 years ago
• Peter-van-Tol / LITEXCNC-HUB75HAT
  A PCB that turns the Colorlight 5A-75B into an easy to use LinuxCNC motion controller
  ☆11Updated last year