Alternatives and similar repositories for spi-fpga-driver

Users that are interested in spi-fpga-driver are comparing it to the libraries listed below

• pekkaroi / ethernetcnc
  ☆14Updated 6 years ago
• mhouse1 / mechsoftronic
  FPGA based CNC Machine
  ☆90Updated 5 years ago
• STMBL / QtServoterm
  Qt version of stmbl Servoterm
  ☆13Updated 2 years ago
• koppi / mk
  My LinuxCNC / EtherCAT notes
  ☆60Updated last month
• deadsy / grbl_stm32f4
  The grbl g-code interpreter ported to the STM32F4
  ☆63Updated 2 years ago
• machinekit / mksocfpga
  Hostmot2 FPGA code for SoC/FPGA platforms from Altera and Xilinx
  ☆32Updated last year
• IRNAS / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆37Updated 9 years ago
• LinuxCNC / hostmot2-firmware
  HostMot2 FPGA firmware
  ☆21Updated 4 years ago
• schue / xenopicnc
  Xenomai + LinuxCNC automatic build script for the Raspberry Pi
  ☆23Updated 10 years ago
• x893 / CNC-STM32
  STM32 based CNC controller
  ☆106Updated 10 years ago
• ottoragam / Tarocco
  Closed Loop Motor Controller
  ☆134Updated 4 years ago
• madcowswe / Servo
  High performance motor control
  ☆90Updated 9 years ago
• dabit20 / dabitusb_cnc
  ☆10Updated 5 years ago
• langwadt / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆33Updated 4 years ago
• Smoothieware / SmoothieV2
  Version 2 smoothie for the STM32H7xx
  ☆33Updated 4 months ago
• helimp / grbl_stm32
  GRBL for STM32 controller. Reference: https://github.com/usbcnc/grbl
  ☆21Updated 5 years ago
• technosar / GRBL_STM32
  An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on a straight ST…
  ☆30Updated 4 years ago
• joewa / bldc-strip
  OpenBLDC Strip (STM32F103)
  ☆67Updated 8 years ago
• Dark-Guan / Ananas
  This is an Arduino based program for step motor controller,Ananas.
  ☆51Updated 8 years ago
• scottalford75 / LinuxCNC-on-RPi
  ☆29Updated 4 years ago
• hzeller / beagleg
  G-code interpreter and stepmotor controller for crazy fast coordinated moves of up to 8 steppers. Uses the Programmable Realtime Unit (PR…
  ☆127Updated last year
• ethercat-diy / arducat
  EtherCAT over arduino (atmega1280)
  ☆54Updated 6 years ago
• machinekit / Cetus
  Full-featured user interface for Machinekit
  ☆35Updated 5 years ago
• lucysrausch / ottercontrol
  Hardware files for OtterControl BLDC motor controller
  ☆65Updated 5 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated last week
• cdsteinkuehler / bobc_hardware
  CRAMPS - A Cape version of the RAMPS-FD design for 3D printing
  ☆45Updated 6 years ago
• KurtJacobson / hazzy
  Touchscreen UI for LinuxCNC
  ☆33Updated 5 years ago
• jarekkt / step2mach
  Plugin for Mach3 and Nucleo-F429ZI board
  ☆17Updated 5 years ago
• grblHAL / Simulator
  grblHAL drivers for simulation (Linux and Windows)
  ☆35Updated 2 weeks ago
• machinekit / machinekit-cnc
  CNC stack split out into a separate package
  ☆65Updated 5 years ago