Alternatives and similar repositories for LinuxCNC_ArduinoConnector:

Users that are interested in LinuxCNC_ArduinoConnector are comparing it to the libraries listed below

• kcjengr / probe_basic
  User interface for the LinuxCNC machine control.
  ☆98Updated 3 weeks ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆145Updated 2 months ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆88Updated last week
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆43Updated 2 months ago
• verser-git / probe_screen_v2
  ☆43Updated 4 years ago
• grblHAL / drivers
  Driver overview
  ☆32Updated last month
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆20Updated 9 months ago
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆47Updated last week
• linuxcnc-probe-screen / probe-screen-ng
  LinuxCNC Probe Screen
  ☆25Updated last year
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆111Updated last year
• TooTall18T / tool_length_probe
  Tool length probe subroutine for Probe Basic.
  ☆17Updated last week
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆59Updated last year
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆75Updated 10 months ago
• wezhunter / ESP32_LinuxCNC_MotionController_RealTime
  ESP32 hardware based real-time LinuxCNC motion controller
  ☆28Updated 10 months ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆41Updated 3 weeks ago
• jschoch / ESPels
  ESP32 electronic leadscrew for a lathe
  ☆23Updated 5 months ago
• G-EDM / G-EDM-v1-deprecated
  The G-EDM is a 4in1 electrical discharge machine that supports sinker EDM, EDM engraving, EDM drilling and Wire EDM operations. In the fu…
  ☆49Updated 6 months ago
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆74Updated 6 months ago
• Expatria-Technologies / grblhal_2000_PrintNC
  Expatria Technologies GRBLHAL Breakout board for PrintNC
  ☆30Updated last year
• GuiHue / probe_screen_v2
  ☆10Updated 5 years ago
• hausen8 / EasyProbe
  Easy to install and easy to use probe panel for LinuxCNC Axis GUI
  ☆14Updated 9 months ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆28Updated 5 months ago
• kentavv / electronic-leadscrew
  Lathe electronic leadscrew controller
  ☆15Updated 4 years ago
• multigcs / riocore
  riocore
  ☆32Updated this week
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 2 weeks ago
• grblHAL / iMXRT1062
  grblHAL driver for NXP iMXRT1062 (Teensy 4.x)
  ☆52Updated this week
• grblHAL / plugins
  Plugins overview
  ☆25Updated last month
• nickshl / SmartPendant
  SmartPendant - a way to control grblHAL based CNC machine without PC
  ☆41Updated 3 weeks ago
• linuxcnc-ethercat / linuxcnc-ethercat
  LinuxCNC EtherCAT HAL driver
  ☆46Updated last week