Alternatives and similar repositories for mksocfpga:

Users that are interested in mksocfpga are comparing it to the libraries listed below

• tinkercnc / spi-fpga-driver
  LinuxCNC to fpga-over-spi driver
  ☆25Updated 8 years ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆61Updated last month
• LinuxCNC / hostmot2-firmware
  HostMot2 FPGA firmware
  ☆20Updated 4 years ago
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆74Updated 6 months ago
• mhouse1 / mechsoftronic
  FPGA based CNC Machine
  ☆89Updated 5 years ago
• Peter-van-Tol / LITEXCNC-HUB75HAT
  A PCB that turns the Colorlight 5A-75B into an easy to use LinuxCNC motion controller
  ☆11Updated last year
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆26Updated last month
• multigcs / riocore
  riocore
  ☆32Updated this week
• Laksen / kicad-bga-tools
  Tools to make life easier for PCB design with BGA's
  ☆45Updated 4 years ago
• pekkaroi / ethernetcnc
  ☆14Updated 6 years ago
• freakontrol / stmbl
  ☆21Updated 3 weeks ago
• madcowswe / ODriveFPGA
  High performance motor control
  ☆100Updated 8 years ago
• cdsteinkuehler / bobc_hardware
  CRAMPS - A Cape version of the RAMPS-FD design for 3D printing
  ☆45Updated 5 years ago
• RAPcores / rapcores
  Robotic Application Processor
  ☆23Updated 3 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated last month
• hzeller / beagleg
  G-code interpreter and stepmotor controller for crazy fast coordinated moves of up to 8 steppers. Uses the Programmable Realtime Unit (PR…
  ☆124Updated last year
• issus / NEMA8-Juki-Tool-Changer
  Pick and Place tool changer nozzle to hold Juki 500 series nozzles on a NEMA8 hollow shaft motor
  ☆28Updated 8 years ago
• tvelliott / dsp_ice
  ICE40 8K FPGA / STM32F4 development system
  ☆61Updated 7 years ago
• madcowswe / Servo
  High performance motor control
  ☆89Updated 8 years ago
• xesscorp / xess_fp_wizard
  A KiCad wizard to assist you in making footprints for chips having pins around the edges (SOICs, QFPs, etc.) and ball grid arrays (BGAs)
  ☆37Updated 5 years ago
• KurtJacobson / hazzy
  Touchscreen UI for LinuxCNC
  ☆32Updated 4 years ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• krtkl / open-source-schematics
  released krtkl schematics
  ☆57Updated 6 years ago
• linuxcnc-ethercat / linuxcnc-ethercat
  LinuxCNC EtherCAT HAL driver
  ☆46Updated last week
• xboxhacker / OpenFeeder
  OpenSource feeder for DIY and OpenPNP community
  ☆32Updated 9 years ago
• scottalford75 / Remora-NVEM
  Remora firmware for Novusun NVEM controller board
  ☆14Updated 3 months ago
• joewa / ChibiESC
  Free electric speed controller software using ChibiOS
  ☆10Updated last year
• clementleger / Smoothieware-STM32
  [DEPRECATED] Modular, opensource, high performance G-code interpreter and CNC controller written in Object-Oriented C++
  ☆38Updated 9 years ago
• dejan-stankovic / meetup-ad-schematic
  Introduction to reverse engineering design file formats as presented on Hardware Developers Didactic Galactic meetup on October 9th
  ☆36Updated 10 years ago
• hstarmans / hexastorm
  Amaranth HDL framework for laser scanner with motion control
  ☆28Updated 3 weeks ago