Alternatives and similar repositories for Didge

Users that are interested in Didge are comparing it to the libraries listed below

• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆61Updated 2 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆118Updated last year
• jschoch / ESPels
  ESP32 electronic leadscrew for a lathe
  ☆23Updated 9 months ago
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆50Updated 3 weeks ago
• RootCNC / Root-Controller-ISO
  ESP32 GRBL Controller for the Root CNC machines
  ☆25Updated last year
• bartei / rotary-controller-f4
  Digital Read Out and Single Axis Controller
  ☆46Updated 3 weeks ago
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆47Updated 4 months ago
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆84Updated last week
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 4 months ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆50Updated 3 months ago
• xpix / XATC
  DIY CNC Automatic Toolchanger
  ☆67Updated 6 years ago
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆75Updated last year
• grblHAL / iMXRT1062
  grblHAL driver for NXP iMXRT1062 (Teensy 4.x)
  ☆53Updated last week
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated last year
• gnea / grbl-LPC
  ☆75Updated 3 years ago
• kachurovskiy / nanoels
  Electronic Lead Screw for metal lathe
  ☆225Updated 3 weeks ago
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆79Updated 10 months ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆157Updated 3 months ago
• Alfrederson / cncstm32
  CNC Base for Blue Pill
  ☆17Updated 6 years ago
• kingoflolz / linear-actuator-hardware
  ☆62Updated 2 years ago
• grblHAL / plugins
  Plugins overview
  ☆26Updated 5 months ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆24Updated last month
• stephenhouser / Arduino-DRO
  Firmware for Arduino DRO with 4 Axis, Tachometer, Touch Probe (http://www.rysium.com/rysium.docs/)
  ☆11Updated last year
• BETZtechnik / ICEpick--Direct-drive-pick-and-place-head
  Pick and Place head with dual nozzles
  ☆39Updated 5 years ago
• ChrisWag91 / PI-LCNC
  Adapter board to use a Raspberry Pi as a Linux CNC controller
  ☆59Updated 2 years ago
• geniekobayashi / juki_nozzle_changer
  OpenPnP project
  ☆17Updated 8 years ago
• ccomito1223 / ELS-Jon
  Electronic Lead Screw - By Jon Bryan
  ☆21Updated 4 years ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆67Updated 3 months ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆91Updated 3 weeks ago
• alextreseder / picoEDM
  Minimalist DIY Wire EDM for Hobbyists & Education
  ☆47Updated 5 months ago