Alternatives and similar repositories for riocore:

Users that are interested in riocore are comparing it to the libraries listed below

• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆61Updated 2 weeks ago
• freakontrol / stmbl
  ☆21Updated last week
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆26Updated last month
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆74Updated 6 months ago
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆70Updated this week
• fdarling / mesa-smartserial-device-template
  Mesa SmartSerial (SSLBP) custom device template project
  ☆11Updated 4 years ago
• machinekit / mksocfpga
  Hostmot2 FPGA code for SoC/FPGA platforms from Altera and Xilinx
  ☆31Updated last year
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆19Updated 9 months ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆143Updated last month
• scottalford75 / LinuxCNC-3D-Printing
  ☆25Updated last year
• linuxcnc-ethercat / linuxcnc-ethercat
  LinuxCNC EtherCAT HAL driver
  ☆44Updated 2 weeks ago
• linuxcnc-probe-screen / probe-screen-ng
  LinuxCNC Probe Screen
  ☆25Updated last year
• MetalMusings / MyOwnEtherCATDevice
  Documentation accompanying the "Make My Own EtherCAT device" video serie on Youtube.
  ☆51Updated last week
• scottalford75 / Remora-NVEM
  Remora firmware for Novusun NVEM controller board
  ☆14Updated 3 months ago
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆43Updated 2 months ago
• G-EDM / GEDM-EVO2-CNC
  Gantry based 3 axis CNC router with heavy duty 3d printed parts and schematics for the boards
  ☆25Updated last month
• FernV / NativeCAM
  NativeCAM for LinuxCNC embeds in axis or gmoccapy interfaces
  ☆47Updated 4 years ago
• Peter-van-Tol / LITEXCNC-HUB75HAT
  A PCB that turns the Colorlight 5A-75B into an easy to use LinuxCNC motion controller
  ☆11Updated last year
• wezhunter / ESP32_LinuxCNC_MotionController_RealTime
  ESP32 hardware based real-time LinuxCNC motion controller
  ☆27Updated 10 months ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 10 months ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated 2 weeks ago
• Deotti-cl / linuxcnc-esp32
  External pulse generator
  ☆17Updated 3 years ago
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• iforce2d / linuxcnc-gcode-server
  Allows connecting to a LinuxCNC installation and executing commands, similar to linuxcncrsh.
  ☆24Updated 3 weeks ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆28Updated 4 months ago
• Laksen / kicad-bga-tools
  Tools to make life easier for PCB design with BGA's
  ☆45Updated 4 years ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆84Updated last month
• cnc-club / linuxcnc-engraving-comp
  Component for engraving non flat surfaces using LinuxCNC
  ☆15Updated 10 years ago
• tinkercnc / spi-fpga-driver
  LinuxCNC to fpga-over-spi driver
  ☆25Updated 8 years ago
• jethornton / flexgui
  A flexible GUI for LinuxCNC
  ☆16Updated last week