Alternatives and similar repositories for MKS-SERVO42C

Users that are interested in MKS-SERVO42C are comparing it to the libraries listed below

• makerbase-mks / MKS-SERVO42B
  MKS SERVO42B is 3d printer closed loop stepper motor NEMA17 MKS SERVO42 developed by Makerbase that prevents losing steps. CPU is STM32F1…
  ☆178Updated 3 years ago
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆117Updated 3 years ago
• makerbase-motor / MKS-SERVO57D
  Makerbase MKS SERVO57D NEMA23 closed loop stepper motor Driver FOC quiet and efficient RS485 / CAN
  ☆63Updated last year
• grblHAL / ESP32
  grblHAL driver for ESP32
  ☆109Updated this week
• creapunk / TMC2209-UART
  An efficient library designed for UART interfacing with the TMC2209 stepper motor driver
  ☆27Updated last year
• Misfittech / nano_stepper
  Stepper feedback controller
  ☆442Updated last year
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆83Updated 2 months ago
• makerbase-mks / MKS-SERVO42A
  Makerbase MKS SERVO42A NEMA17 closed loop stepper motor Driver CNC 3d printer parts prevents losing steps for Gen_L SGen_L
  ☆59Updated 3 years ago
• makerbase-mks / MKS-StepStick-Driver
  Include MKS TMC2209, MKS TMC2225, MKS TMC2208, MKS TB67S109 and so on
  ☆69Updated 2 years ago
• bigtreetech / BIGTREETECH-S42B-V1.0
  The closed-loop drive is to feedback the rotation angle of the stepping motor to the control panel, compare the distance that needs to be…
  ☆113Updated 4 years ago
• janelia-arduino / TMC2209
  The TMC2209 is an ultra-silent motor driver IC for two phase stepper motors with both UART serial and step and direction interfaces.
  ☆278Updated last month
• grblHAL / STM32F4xx
  grblHAL driver for ST STM32F4xx (Nucleo-64, Blackpill)
  ☆125Updated this week
• makerbase-mks / MKS-DLC
  MKS DLC support grbl firmware, can use Laser mode and CNC mode,support connect MKS TFT24/32/35 and TFT_CNC firmware support lasering and …
  ☆102Updated 3 years ago
• zapta / simple_stepper_motor_analyzer
  A DYI stepper motor analyzer. This is a new design that is based on Raspberry Pi Pico and users a compact single PCB design. NOTE: The l…
  ☆153Updated 2 years ago
• creapunk / TunePulse
  Firmware for CLN and RadiX motor drivers
  ☆22Updated last year
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆74Updated 5 years ago
• mstrens / grbl_controller_esp32
  grbl controller for esp32
  ☆202Updated 2 years ago
• PixiePlacer / PixiePlacer
  The PixiePlacer is a DIY Pick and Place Machine for SMD Components running OpenPnP.
  ☆126Updated last year
• grblHAL / core
  grblHAL core code and master Wiki
  ☆433Updated this week
• maplerainresearch / MRR_ESPE
  MRR ESPE 3D printer control board
  ☆38Updated 5 years ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆155Updated last year
• pvico / grbl32
  CNC controller running on the STM32F103 "Blue Pill" board, build and flash on Mac/Linux
  ☆68Updated 4 years ago
• byDagor / Dagor-Brushless-Controller
  The Dagor Controller is a fully integrated tiny solution for brushless-based actuators with wireless capabilities.
  ☆364Updated 3 months ago
• simplefoc / SimpleFOCMini
  Small package, low-cost BLDC diver board fully compatible with the simplefoc library
  ☆136Updated last year
• bdring / 6-Pack_CNC_Controller
  ☆319Updated 2 years ago
• thomast777 / grbl32
  GRBL 1.1f CNC Controller forked/ported to STM32 ARM : STM32F103 and STM32F407
  ☆211Updated 5 years ago
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆147Updated this week
• grblHAL / drivers
  Driver overview
  ☆37Updated 8 months ago
• ghent360 / PrntrBoardV2
  32-bit 3D Printer controller board using STM32F407 and replaceable TMC2660/2209 stepper drivers.
  ☆43Updated 4 years ago
• byDagor / Janus-Controller
  The Janus Controller is a Brushless motor driver with an on-board magnetic encoder, a three-phase MOSFET driver, three MOSFET half-bridge…
  ☆129Updated 4 years ago