Alternatives and similar repositories for stmbl:

Users that are interested in stmbl are comparing it to the libraries listed below

• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆77Updated 8 months ago
• multigcs / riocore
  riocore
  ☆44Updated this week
• fdarling / mesa-smartserial-device-template
  Mesa SmartSerial (SSLBP) custom device template project
  ☆11Updated 5 years ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆64Updated last month
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆77Updated last month
• linuxcnc-ethercat / linuxcnc-ethercat
  LinuxCNC EtherCAT HAL driver
  ☆48Updated 3 weeks ago
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆27Updated 3 months ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆21Updated 3 weeks ago
• scottalford75 / LinuxCNC-3D-Printing
  ☆25Updated 2 years ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆152Updated 3 weeks ago
• MetalMusings / MyOwnEtherCATDevice
  Documentation accompanying the "Make My Own EtherCAT device" video serie on Youtube.
  ☆59Updated last month
• wezhunter / ESP32_LinuxCNC_MotionController_RealTime
  ESP32 hardware based real-time LinuxCNC motion controller
  ☆32Updated last year
• Deotti-cl / linuxcnc-esp32
  External pulse generator
  ☆17Updated 4 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated last month
• FernV / NativeCAM
  NativeCAM for LinuxCNC embeds in axis or gmoccapy interfaces
  ☆47Updated 4 years ago
• pcm52 / DRO-V6
  Digital Readout sketch files for the Arduino IDE
  ☆10Updated 4 years ago
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆43Updated 4 months ago
• futurelink / linuxcnc-spindle-encoder
  A small AVR controller and a component to connect high precision encoder to LinuxCNC via Modbus RTU
  ☆18Updated 5 years ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆61Updated last year
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆31Updated 7 months ago
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆34Updated 2 years ago
• machinekit / mksocfpga
  Hostmot2 FPGA code for SoC/FPGA platforms from Altera and Xilinx
  ☆31Updated last year
• scottalford75 / Remora-NVEM
  Remora firmware for Novusun NVEM controller board
  ☆14Updated 5 months ago
• hausen8 / EasyProbe
  Easy to install and easy to use probe panel for LinuxCNC Axis GUI
  ☆14Updated 11 months ago
• linuxcnc-probe-screen / probe-screen-ng
  LinuxCNC Probe Screen
  ☆25Updated last year
• iforce2d / linuxcnc-gcode-server
  Allows connecting to a LinuxCNC installation and executing commands, similar to linuxcncrsh.
  ☆27Updated 3 months ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆89Updated last month
• ExcessiveMotion / drive-hardware
  ☆10Updated last year
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 2 months ago