Alternatives and similar repositories for hostmot2-firmware:

Users that are interested in hostmot2-firmware are comparing it to the libraries listed below

• pekkaroi / ethernetcnc
  ☆14Updated 6 years ago
• Deotti-cl / linuxcnc-esp32
  External pulse generator
  ☆17Updated 3 years ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆20Updated 9 months ago
• tinkercnc / spi-fpga-driver
  LinuxCNC to fpga-over-spi driver
  ☆25Updated 8 years ago
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• machinekit / mksocfpga
  Hostmot2 FPGA code for SoC/FPGA platforms from Altera and Xilinx
  ☆31Updated last year
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• fdarling / mesa-smartserial-device-template
  Mesa SmartSerial (SSLBP) custom device template project
  ☆11Updated 4 years ago
• makerbase-mks / MKS-SERVO57B
  MKS SERVO57B is 3d printer closed loop stepper motor NEMA23 MKS SERVO57 developed by Makerbase that prevents losing steps. CPU is STM32F1…
  ☆21Updated 3 years ago
• futurelink / linuxcnc-spindle-encoder
  A small AVR controller and a component to connect high precision encoder to LinuxCNC via Modbus RTU
  ☆18Updated 5 years ago
• buildbotics / bbctrl-pcb
  Buildbotics CNC, 3D printer and other machine controller
  ☆49Updated 3 years ago
• cdsteinkuehler / bobc_hardware
  CRAMPS - A Cape version of the RAMPS-FD design for 3D printing
  ☆45Updated 5 years ago
• Smoothieware / SmoothieV2-LPC
  Smoothie for Version2 boards
  ☆38Updated 3 years ago
• grblHAL / plugins
  Plugins overview
  ☆25Updated last month
• Alfrederson / cncstm32
  CNC Base for Blue Pill
  ☆16Updated 6 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated last month
• terjeio / CNC_Breakout_Nucleo64
  CNC breakout for STM324F411 and ST32F446 development boards
  ☆21Updated 2 years ago
• ryannining / karyacontroller
  4 axis CNC, 3D, Laser Controller
  ☆59Updated 4 months ago
• dungjk / grbl-stm32
  An open source, embedded, high performance g-code-parser and CNC milling controller. This is a port of GRBL 1.1 to STM32F10X target.
  ☆78Updated 2 years ago
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆26Updated last month
• scottalford75 / Remora-NVEM
  Remora firmware for Novusun NVEM controller board
  ☆14Updated 3 months ago
• MachineryScience / Rockhopper
  Machinery Science LinuxCNC remote access, configuration and utilities
  ☆17Updated 6 years ago
• langwadt / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆33Updated 3 years ago
• Peter-van-Tol / LITEXCNC-HUB75HAT
  A PCB that turns the Colorlight 5A-75B into an easy to use LinuxCNC motion controller
  ☆11Updated last year
• paulusjacobus / SuperGerbil
  STM32 driven ARM Grbl firmware
  ☆23Updated 5 years ago
• scottalford75 / LinuxCNC-3D-Printing
  ☆25Updated last year
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆28Updated 5 months ago
• buildbotics / bbctrl-firmware
  Buildbotics CNC Controller Firmware
  ☆69Updated last month
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆74Updated 6 months ago
• jethornton / mesact1
  ☆24Updated last year