Alternatives and similar repositories for drive-hardware

Users that are interested in drive-hardware are comparing it to the libraries listed below

• CrabLabsLLC / OpenMD
  ☆146Updated 11 months ago
• opulo-inc / feeder
  Source for LumenPnP Feeders
  ☆164Updated 3 weeks ago
• kingoflolz / linear-actuator-hardware
  ☆65Updated 3 years ago
• 0x23 / QuietAirCompressor
  A small and quiet air compressor design using 3D printed parts where possible.
  ☆92Updated last year
• 0x23 / MicroManipulator
  An open source low-cost, easy-to-build XYZ Micro-Manipulator platform.
  ☆196Updated 3 months ago
• owhite / MP2-DFN
  A variant of the MP2 electronic speed control with DFNW MOSFETs
  ☆25Updated last year
• photonfirmware / photon
  Open-Source firmware for pick and place feeders
  ☆67Updated 3 weeks ago
• alextreseder / WEDM
  Minimalist DIY Wire EDM for Hobbyists & Education
  ☆71Updated 3 months ago
• BoltzRnD / SmartPrintCoreH7x
  STM32H7 based Robust and Open Source 3D Printer Mainboard
  ☆70Updated 2 months ago
• Rack-Robotics / Powercore-V1.0-Hardware
  CAD & Electronics for Powercore V1
  ☆158Updated last year
• markmaker / PushPullFeeder
  All 3d-Printed Tape&Reel Feeder
  ☆80Updated last year
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆158Updated this week
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆66Updated 4 months ago
• opulo-inc / paste-extruder
  Paste extruder head for the LumenPnP
  ☆56Updated 3 months ago
• Rack-Robotics / Powercore-V2.0
  Open-Source wire EDM power supply by Rack Robotics, Inc.
  ☆202Updated last year
• NoEngineerHere / TeensyELS
  ☆55Updated 3 months ago
• ploopyco / pnp-feeder
  An automated feeder for pick and place machines.
  ☆160Updated 5 years ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆63Updated 2 years ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆164Updated 4 months ago
• 0x23 / open-air-bearings
  Techniques and software to build, design and simulate air bearings
  ☆53Updated last year
• freakontrol / stmbl
  ☆35Updated 4 months ago
• Twisted-Fields / rp2040-motor-controller
  A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.
  ☆404Updated last year
• iforce2d / linuxcnc-gcode-server
  Allows connecting to a LinuxCNC installation and executing commands, similar to linuxcncrsh.
  ☆32Updated 10 months ago
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆150Updated this week
• robin7331 / pixel-pump-mainboard
  ☆49Updated 2 years ago
• KoshiroRobot / FOC-Driver
  ☆97Updated 4 months ago
• Andrew-Dickinson / photonic-etcher
  Generate exposure masks for Anycubic printers from PCB Gerbers
  ☆100Updated last year
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated 2 years ago
• atomic14 / kicad-coil-plugins
  Some simple plugins for generating stator coils in kicad
  ☆107Updated last year
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆80Updated last year