Alternatives and similar repositories for xESC2040

Users that are interested in xESC2040 are comparing it to the libraries listed below

• danjulio / tCam
  Thermal imaging cameras based on the ESP32 and Lepton 3.5
  ☆132Updated last year
• pgrady3 / EasyController3
  A simple BLDC motor controller, and the evolution of the EasyController2
  ☆94Updated last year
• kingoflolz / linear-actuator-hardware
  ☆66Updated 3 years ago
• owennewo / simplefoc_skateboard_g431b
  ☆30Updated 5 years ago
• kingoflolz / linear-actuator-firmware
  ☆31Updated 3 years ago
• aeonSolutions / PCB-Prototyping-Catalogue
  There are now, a total of 81 hardware electronics on this catalogue for Smart Devices, A.I. enabled. Designed in Kicad, and ready to dow…
  ☆95Updated last year
• wagiminator / ADuM3160-USB-Isolator
  2.5kV USB 2.0 Isolator with 200mA Power Supply and Full Speed (12Mbps) Support
  ☆67Updated 3 years ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆41Updated last year
• EFeru / hoverboard-firmware-hack-SIN
  With SINUSOIDAL BLDC control. Offers much quieter and smoother motor operation.
  ☆47Updated 3 years ago
• simplefoc / Arduino-FOC-dcmotor
  Control DC motors using SimpleFOC's infrastructure
  ☆32Updated last year
• badgineer / MP2-ESC
  Multi-Platform, Modular, Powerful ESC
  ☆130Updated last year
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆67Updated 5 months ago
• CrabLabsLLC / OpenMD
  ☆147Updated last year
• owhite / brushless_gimbal_motor
  ☆22Updated 8 years ago
• rambros3d / MicroSpora-SimpleFOC
  ☆29Updated last year
• Luisonson / LibreServo_v2
  An Open source controller to convert any servo motor to the best smart servo. Servomotor Hack
  ☆35Updated last year
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 9 years ago
• EnnoidMe / ENNOID-BMS-Tool
  The ENNOID-BMS Tool can be used to configure ENNOID-BMS.
  ☆38Updated 2 years ago
• Igitigit2 / SimpleCanLib
  CAN bus library for ESP32 and STM32 G431
  ☆34Updated last year
• paulvee / 100MHz-Differential-Probe
  100 MHz Differential Probe V2
  ☆53Updated last year
• mrmp17 / FOCn
  ESP32-S3 based SimpleFOC compatible BLDC driver module
  ☆59Updated last year
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆76Updated 2 months ago
• jkirsons / BLDC-Driver-IFX007T
  ☆25Updated 4 years ago
• richardklingler / openpnp
  My pick and place machine controlled by the great OpenPNP software.
  ☆77Updated 4 years ago
• iforce2d / linuxcnc-gcode-server
  Allows connecting to a LinuxCNC installation and executing commands, similar to linuxcncrsh.
  ☆32Updated 10 months ago
• owhite / MP2-DFN
  A variant of the MP2 electronic speed control with DFNW MOSFETs
  ☆26Updated last year
• ClemensElflein / xESC
  The xESC is an easy to use, low cost electronic speed controller (ESC) design for sensored brushless DC (BLDC) motors.
  ☆355Updated 5 months ago
• dmitrystu / nuco-v
  NUCLEO-64 compatible board for the STM32F7 and STM32H7 series
  ☆25Updated 4 years ago
• bipropellant / bipropellant-protocol
  defines and implements a low level protocol shared between a few different hoverboard repositories
  ☆22Updated 5 years ago
• Vidicon / camsense-X1
  unofficial reverse engineering of a Chinese LiDAR. Discussed this on my discord: https://discord.gg/zRGJcqa
  ☆65Updated 5 years ago