Alternatives and similar repositories for MP2-DFN:

Users that are interested in MP2-DFN are comparing it to the libraries listed below

• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆31Updated 6 months ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆61Updated last year
• bartei / rotary-controller-f4
  Digital Read Out and Single Axis Controller
  ☆43Updated 8 months ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆32Updated last year
• BoltzRnD / SmartPrintCoreH7x
  STM32H7 based Robust and Open Source 3D Printer Mainboard
  ☆53Updated 4 months ago
• liba2k / VINCA_reader
  ☆48Updated 9 months ago
• kingoflolz / linear-actuator-firmware
  ☆29Updated 2 years ago
• alextreseder / picoEDM
  Minimalist DIY Wire EDM for Hobbyists & Education
  ☆45Updated 2 months ago
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆34Updated last year
• BEEMB / Battery-Health-Monitor
  Battery Health Monitor A compact device for monitoring the State of Health (SoH) and State of Charge (SoC) of lithium batteries. It uses …
  ☆22Updated 2 weeks ago
• kingoflolz / linear-actuator-hardware
  ☆60Updated 2 years ago
• nickshl / SmartPendant
  SmartPendant - a way to control grblHAL based CNC machine without PC
  ☆42Updated last week
• jfedor2 / magellan-spacemouse
  Adapter to use RS-232 Magellan/SpaceMouse with modern software
  ☆41Updated 2 years ago
• Rack-Robotics / EDMWeb
  EDM CAM software for generating EDM gcode
  ☆25Updated last year
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆77Updated last week
• bartei / rotary-controller-pcb
  Rotary Controller PCB
  ☆31Updated last year
• kentavv / electronic-leadscrew
  Lathe electronic leadscrew controller
  ☆15Updated 4 years ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆20Updated last week
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆64Updated 2 weeks ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated last month
• enp6s0 / TinySparrow
  All-in-one CAN ECU core board
  ☆34Updated 4 months ago
• ExcessiveMotion / drive-hardware
  ☆10Updated last year
• avandalen / PCB-Spotwelder-Controller
  ☆10Updated 3 years ago
• ftobler / pick-plaz
  Open source pick and place machine
  ☆24Updated 7 months ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆42Updated last month
• makerstorage / pnpAssist
  PNPASSIST: A “SMART” BUILD PLATFORM FOR MANUAL PCB ASSEMBLY
  ☆42Updated 3 years ago
• zapta / ble_stepper_motor_analyzer
  A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
  ☆50Updated last year
• arsi-apli / BLDC_Klipper_doc
  This is documentation for a modified version of the Klipper firmware that allows you to directly drive a BLDC Motor in an open loop confi…
  ☆18Updated 2 years ago
• atc1441 / ATC_stc_solder_iron
  Custom firmware for cheap STC Based Soldering iron using PlatformIO and SDCC 8051 based
  ☆50Updated 2 years ago
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆43Updated 3 months ago