Alternatives and similar repositories for drive-software

Users that are interested in drive-software are comparing it to the libraries listed below

• ExcessiveMotion / brake-module-hardware
  ☆20Updated 2 years ago
• ExcessiveMotion / controller-hardware
  ☆64Updated 4 months ago
• ExcessiveMotion / pendant-hardware
  ☆20Updated 2 years ago
• ExcessiveMotion / drive-hardware
  ☆142Updated 4 months ago
• kingoflolz / linear-actuator-hardware
  ☆66Updated 3 years ago
• owhite / MP2-DFN
  A variant of the MP2 electronic speed control with DFNW MOSFETs
  ☆26Updated last year
• fasaxc / pico-bldc
  RP2040-based BLDC motor controller
  ☆43Updated last year
• kingoflolz / linear-actuator-firmware
  ☆31Updated 3 years ago
• 0x23 / MicroManipulator
  An open source low-cost, easy-to-build XYZ Micro-Manipulator platform.
  ☆211Updated 5 months ago
• sphawes / fiber-laser-pcb-fab
  Instructions and settings for fabricating PCBs on a fiber laser, namely the xTool F1 Ultra
  ☆132Updated 3 weeks ago
• 0x23 / QuietAirCompressor
  A small and quiet air compressor design using 3D printed parts where possible.
  ☆95Updated last year
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆67Updated 6 months ago
• CrabLabsLLC / OpenMD
  ☆147Updated last year
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆64Updated 2 years ago
• ExcessiveMotion / controller-software
  ☆122Updated 6 months ago
• jakeread / mudlink
  Modular UART Duplex Link: cobs, crc, flow-control and delivery guarantees on any UART port in Arduino
  ☆27Updated last year
• EmanuelBender / HEX_POD
  Multi-sensor intelligent environmental Monitor
  ☆18Updated last year
• wagiminator / ADuM3160-USB-Isolator
  2.5kV USB 2.0 Isolator with 200mA Power Supply and Full Speed (12Mbps) Support
  ☆68Updated 3 years ago
• knifter / DualPID
  Multi Channel Configurable PID regulator on M5Stack Core
  ☆50Updated last year
• BoltzRnD / SmartPrintCoreH7x
  STM32H7 based Robust and Open Source 3D Printer Mainboard
  ☆73Updated 4 months ago
• opulo-inc / paste-extruder
  Paste extruder head for the LumenPnP
  ☆61Updated last week
• liba2k / VINCA_reader
  ☆55Updated last year
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆42Updated last year
• pmarques-dev / PicoEncoder
  High resolution quadrature encoder using the PIO on the RP2040
  ☆66Updated 8 months ago
• 0x23 / open-air-bearings
  Techniques and software to build, design and simulate air bearings
  ☆57Updated last year
• MitkoDyakov / Calipatron
  I design my own digital caliper based on STM32F103C8T6 blue pill.
  ☆39Updated last week
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated 2 years ago
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆33Updated last year
• BirdbrainEngineer / microscope-upgrade
  Microscope upgrade with xyz stage and 2K camera stream
  ☆15Updated last year
• iforce2d / linuxcnc-gcode-server
  Allows connecting to a LinuxCNC installation and executing commands, similar to linuxcncrsh.
  ☆33Updated 11 months ago