Alternatives and similar repositories for xy2_100

Users that are interested in xy2_100 are comparing it to the libraries listed below

• 412910609 / galvoMC
  1、XY2-100协议的解析；2、振镜X、Y电机脉冲的生成；3、编码器数据采集。
  ☆27Updated 5 years ago
• leswright1977 / OPAL_PCB
  PCB deign for OpenGalvo OPAL
  ☆23Updated 3 years ago
• CalvinHsu1223 / LinuxCNC-EtherCAT-HAL-Driver
  LinuxCNC HAL EtherCAT Driver and example files for Panasoniic A5B series servo motors.
  ☆19Updated 10 years ago
• IRNAS / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆37Updated 9 years ago
• tomlarkworthy / linuxCNC_ROS
  connects linuxCNC software to the robot operating system
  ☆17Updated 13 years ago
• ming-orz / linear_encoder_head
  Low-cost, high-resolution grating ruler reading head.
  ☆24Updated 2 years ago
• janelia-arduino / TMC429
  The Trinamic TMC429 is a triple-axis dedicated step and direction motion controller for both position and velocity control with accelerat…
  ☆43Updated 3 weeks ago
• Dark-Guan / AnanasBoard
  ☆28Updated 8 years ago
• Tuet / XY2_100
  XY2_100 library for Teensy 3.2 / LC (Arduino)
  ☆31Updated 6 years ago
• opengalvo / OPAL
  Minimalistic FW for Processing GCode to Galvanometer signals
  ☆101Updated last year
• brendanwong / g-code-generator
  Cross-platform G-Code extrusion command generator for well-plates and petri dishes
  ☆19Updated 5 years ago
• technosar / GRBL_STM32
  An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on a straight ST…
  ☆36Updated 5 years ago
• Dark-Guan / Ananas
  This is an Arduino based program for step motor controller,Ananas.
  ☆51Updated 8 years ago
• dccharacter / STM32_Servo_Controller
  STM32-based servo/CNC/3D-printer controller
  ☆44Updated 13 years ago
• x893 / CNC-STM32
  STM32 based CNC controller
  ☆110Updated 10 years ago
• machinekit / EMCApplication
  Machinekit Featured Application for Enhanced Motion Controller from LinuxCNC
  ☆15Updated 4 years ago
• hyperstepper / NEMA17-HyperStepper
  Open source hardware - NEMA17 closed-loop stepper motor and driver
  ☆41Updated 6 years ago
• MillerRen / grbl-learning
  grbl源码精读与解析，代码行级中文注释，包含详细例程
  ☆51Updated 5 months ago
• nwertzberger / OpenPLC
  OpenPLC is an open source PLC Hardware board. Think Arduino, but change the language used, up the voltage levels, and add a built-in Eth…
  ☆79Updated 6 years ago
• weifengdq / BLDC_DRV11873
  A BLDC Control Project With DRV11873 Driver, STM32F030F4P6 MCU, OLED, Speed and Current Detection etc.
  ☆15Updated 9 years ago
• andreili / STM32-PLC
  The project is open source and open hardware, the purpose of which is to create a PLC based on STM32 MCU's.
  ☆63Updated 8 years ago
• deadsy / grbl_stm32f4
  The grbl g-code interpreter ported to the STM32F4
  ☆64Updated 2 years ago
• koppi / mk
  My LinuxCNC / Machinekit and EtherCAT notes.
  ☆59Updated 6 months ago
• suda-morris / FreeECAT
  EtherCAT Slave(XMC4800) and Master(IgH), Open source both in hardware and software
  ☆58Updated 8 years ago
• mstrens / grbl_6axis_on_stm32
  grbl_6axis_on_stm32
  ☆60Updated 5 years ago
• tinkercnc / spi-fpga-driver
  LinuxCNC to fpga-over-spi driver
  ☆25Updated 9 years ago
• lipoyang / SOEM4Arduino
  Simple Open EtherCAT Master Library for Arduino
  ☆75Updated 4 years ago
• qiayuanl / DArm
  A desktop arm that can write and draw.
  ☆52Updated 8 years ago
• madcowswe / ODriveFPGA
  High performance motor control
  ☆105Updated 9 years ago
• omuzychko / StepperHub
  3-axis UART Stepper Hub for 20$ (STM32 Nucleo 64 & Arduino CNC Shield)
  ☆77Updated 9 years ago