Alternatives and similar repositories for OPAL

Users that are interested in OPAL are comparing it to the libraries listed below

• leswright1977 / OPAL_PCB
  PCB deign for OpenGalvo OPAL
  ☆23Updated 3 years ago
• NiklasHammerstone / GalvoStep
  Project for building a cheap galvo laser system using Stepper motors and widely available parts.
  ☆56Updated last year
• qiayuanl / OpenMGSLS
  Open source Mirror Galvanometer SLS 3D printer.
  ☆76Updated 3 years ago
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆117Updated 3 years ago
• ottoragam / Tarocco
  Closed Loop Motor Controller
  ☆135Updated 4 years ago
• janelia-arduino / TMC429
  The Trinamic TMC429 is a triple-axis dedicated step and direction motion controller for both position and velocity control with accelerat…
  ☆43Updated 2 months ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 9 years ago
• makerbase-mks / MKS-SERVO42B
  MKS SERVO42B is 3d printer closed loop stepper motor NEMA17 MKS SERVO42 developed by Makerbase that prevents losing steps. CPU is STM32F1…
  ☆178Updated 3 years ago
• Smoothieware / Smoothieboard2
  Hardware files for the Smoothieboard v2, and extension boards
  ☆60Updated 3 months ago
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆66Updated 3 months ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆37Updated 2 years ago
• wezhunter / ESP32_LinuxCNC_MotionController_RealTime
  ESP32 hardware based real-time LinuxCNC motion controller
  ☆48Updated last year
• CarlBugeja / PCB-Motor-v4
  ☆174Updated 2 years ago
• kingoflolz / linear-actuator-hardware
  ☆65Updated 3 years ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆164Updated 3 months ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆155Updated last year
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆147Updated this week
• cmore839 / DIY-Linear-Motor
  ☆40Updated last year
• 0x23 / open-air-bearings
  Techniques and software to build, design and simulate air bearings
  ☆53Updated last year
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆35Updated 3 years ago
• uStepper / uStepperS
  ☆53Updated 2 years ago
• Dark-Guan / Ananas
  This is an Arduino based program for step motor controller,Ananas.
  ☆51Updated 8 years ago
• Schildkroet / GRBL-Advanced
  Grbl-Advanced is a no-compromise, high performance, low cost alternative for CNC milling. This version of Grbl runs on a STM32F411RE / ST…
  ☆299Updated last year
• openpnp / openpnp-openbuilds
  An OpenPnP compatible SMT pick and place machine based on OpenBuilds linear motion components.
  ☆232Updated 8 years ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆73Updated last month
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆63Updated 2 years ago
• fra589 / cn5X
  cn5X++ is a new 5/6 axis Grbl control panel to implement all the grbl-Mega-5X capabilities.
  ☆81Updated last year
• Schildkroet / Candle2
  GRBL control interface in Qt.
  ☆223Updated this week
• Denvi / FlatCAM
  https://bitbucket.org/jpcgt/flatcam
  ☆99Updated last month
• 0x23 / nmWave-Interferometer
  An Open Source Interferometer for Accurate Distance Measurements
  ☆76Updated 2 months ago