Alternatives and similar repositories for EMCApplication:

Users that are interested in EMCApplication are comparing it to the libraries listed below

• machinekit / machinekit-cnc
  CNC stack split out into a separate package
  ☆62Updated 4 years ago
• koppi / mk
  LinuxCNC / Machinekit and EtherCAT notes.
  ☆59Updated 2 years ago
• STMBL / QtServoterm
  Qt version of stmbl Servoterm
  ☆12Updated 2 years ago
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• tinkercnc / spi-fpga-driver
  LinuxCNC to fpga-over-spi driver
  ☆25Updated 8 years ago
• CalvinHsu1223 / LinuxCNC-EtherCAT-HAL-Driver
  LinuxCNC HAL EtherCAT Driver and example files for Panasoniic A5B series servo motors.
  ☆18Updated 9 years ago
• grblHAL / Simulator
  grblHAL drivers for simulation (Linux and Windows)
  ☆28Updated this week
• LinuxCNC / hostmot2-firmware
  HostMot2 FPGA firmware
  ☆20Updated 3 years ago
• Deotti-cl / linuxcnc-esp32
  External pulse generator
  ☆17Updated 3 years ago
• Hoektronics / Shukongji
  Experimental Open Hardware CNC system.
  ☆21Updated 11 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated last month
• dbraun1981 / hal-cia402
  linuxcnc hal interface for CiA402 Drives
  ☆30Updated last year
• grotius-cnc / hal-core
  cnc and robot realtime controller. runs on a hal kernel module.
  ☆47Updated 2 years ago
• grotius-cnc / qt_c_linuxcnc_interface_gui
  Linuxcnc interface gui based on halcommands and emc-nml messages, can read and visualise gcode
  ☆14Updated 4 years ago
• machinekit / machinekit-hal
  Universal framework for machine control based on Hardware Abstraction Layer principle
  ☆110Updated 4 months ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• tomlarkworthy / linuxCNC_ROS
  connects linuxCNC software to the robot operating system
  ☆16Updated 12 years ago
• TurBoss / JauriaCNC
  Minimial featured linuxcnc interface
  ☆9Updated last year
• thiagoralves / OpenPLC-Neo
  A cheap, reliable, expandable and, of course, open source device that works with OpenPLC software
  ☆21Updated 6 years ago
• MachineryScience / Rockhopper
  Machinery Science LinuxCNC remote access, configuration and utilities
  ☆17Updated 6 years ago
• pekkaroi / ethernetcnc
  ☆14Updated 6 years ago
• picatostas / cnc_interface
  ROS node to interface cnc machines using GRBL as GCODE interpreter
  ☆11Updated 5 years ago
• SimeonSimeonovIvanov / DC-Servo
  Analog speed control of Brushed DC Motor
  ☆24Updated last year
• FOSSEE / OpenPLC
  ☆40Updated 2 years ago
• Klafyvel / SiviCNCDriver
  An application to send G-Codes and control my milling machine.
  ☆20Updated 2 years ago
• txpzyr / xy2_100
  振镜xy2-100协议ESP32控制代码
  ☆12Updated 4 years ago
• buildbotics / bbctrl-firmware
  Buildbotics CNC Controller Firmware
  ☆68Updated 2 weeks ago
• ManiacalLabs / GalvoDriver
  Galvanometer Controller, DAC and Audio In
  ☆11Updated 4 years ago
• ethercat-diy / arducat
  EtherCAT over arduino (atmega1280)
  ☆52Updated 6 years ago
• cdsteinkuehler / LinuxCNC-RepRap
  Code and configurations to use LinuxCNC to control a RepRap 3D printer
  ☆20Updated 12 years ago