Alternatives and similar repositories for klipper_config

Users that are interested in klipper_config are comparing it to the libraries listed below

• dmitry-sorkin / k3d-minifeeder
  Miniature LGX Lite - compatible 3D printer feeder
  ☆27Updated 2 years ago
• silver-alx / sbc
  Popular SBC linux images
  ☆28Updated 3 months ago
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆102Updated 2 years ago
• pavluchenkor / iDryerController
  ☆44Updated 2 weeks ago
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆21Updated last year
• dmitry-sorkin / BeMeGe
  BeMeGe extruder is BMG reverse, optimized for 3d printing
  ☆59Updated last year
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• Tombraider2006 / K1
  creality k1 helpfull manuals for user. config, mods, hacks
  ☆137Updated last week
• CODeRUS / klipper_extras
  Extras
  ☆18Updated last year
• cryoz / K1_tenso_manual
  ☆30Updated 11 months ago
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆247Updated 2 years ago
• vladimir-poleh / klipper-config
  ☆10Updated last year
• willngton / 3DPrinterConfig
  My 3D Printers Configuration backup - Marlin and Klipper
  ☆44Updated 2 years ago
• condottab / Roborock-CPAP
  CPAP cooling system using a Roborock fan
  ☆96Updated last year
• Vassssko / Voron-2.4-HV-electronic-compartment-mod
  Voron 2.4 clamps set to put many more things into the electronics compartment comparing to baseline.
  ☆18Updated 3 years ago
• Sergey1560 / fb4s_howto
  Howto
  ☆77Updated last year
• K1-Klipper / installer_script_k1_and_max
  ☆54Updated 11 months ago
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆35Updated last year
• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆86Updated last year
• altzbox / Chopper-tuning-guide
  ☆27Updated last year
• makerbase-mks / MKS-SKIPR
  MKS SKIPR is an all-in-one board launched by Makerbase for running Klipper. It integrates the RK3328 SOC running the Klipper host and the…
  ☆111Updated 2 years ago
• kemsky / creality-k1-max-xy-rails-mod
  Creality K1 Max XY Rails Mod
  ☆33Updated 3 months ago
• Chiffa-C3 / Shark-Extruder
  Экструдер разработанный для замены стандартного на принтере FBG6
  ☆24Updated 2 years ago
• stas2z / orange-pi-images
  Prebuilt orange pi images for selected boards with separate FAT boot partition
  ☆12Updated last year
• tlace17 / K1-Flanged-Bearing-Project
  D3D community based K1 and K1 Max Gantry Mod
  ☆36Updated last year
• armysolo / BLV-Cube
  Mods for BLV Cube
  ☆42Updated 2 years ago
• goopypanther / klipper_network_status
  Klipper plugin to make system IP/etc available to macros
  ☆59Updated last year
• worksasintended / klipper_linear_movement_analysis
  ☆74Updated last year
• dmitry-sorkin / k3d-accuracy-test
  FDM 3D Print accuracy test
  ☆29Updated 2 years ago
• ThatGuyHes / Dual-Extruder-X4
  Dual Extruder X4: Nothing like the last one.
  ☆32Updated 9 months ago