Alternatives and similar repositories for klipper_extras

Users that are interested in klipper_extras are comparing it to the libraries listed below

• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆25Updated 5 months ago
• CODeRUS / klipper_config
  ☆28Updated last year
• condottab / Roborock-CPAP
  CPAP cooling system using a Roborock fan
  ☆108Updated 2 years ago
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆259Updated 3 years ago
• Lzhikai / SIBOOR-Voron-2.4
  ☆22Updated 2 years ago
• worksasintended / klipper_linear_movement_analysis
  ☆76Updated 2 years ago
• altzbox / Chopper-tuning-guide
  ☆27Updated last year
• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆106Updated 2 years ago
• henrikssn / TurboCAN
  This is the official repository for the TurboCAN controller board, designed specifically for the Voron AfterBurner toolhead but can also …
  ☆79Updated 4 years ago
• maz0r / instagoo
  Not my recipe, but needed somewhere to point a QR code at for instructions to mix that would be accessible to anyone.
  ☆17Updated 2 years ago
• stas2z / orange-pi-images
  Prebuilt orange pi images for selected boards with separate FAT boot partition
  ☆16Updated 2 years ago
• K1-Klipper / installer_script_k1_and_max
  ☆60Updated last year
• goopypanther / klipper_network_status
  Klipper plugin to make system IP/etc available to macros
  ☆67Updated 2 years ago
• makerbase-mks / MKS-SKIPR
  MKS SKIPR is an all-in-one board launched by Makerbase for running Klipper. It integrates the RK3328 SOC running the Klipper host and the…
  ☆121Updated 3 years ago
• Yumi-Lab / YUMI_PLR
  Power loss recovery for klipper
  ☆40Updated last year
• RomRider / klipper-FastGyroidInfill
  A set of postprocessing scripts and macro to accelerate the gyroid infill print speed with Klipper
  ☆131Updated 4 years ago
• silver-alx / sbc
  Popular SBC linux images
  ☆30Updated last year
• orobardet / klipper_nano_expander
  Klipper Nano Expander, an Arduino Nano Shield to be used as an auxiliary Klipper MCU
  ☆35Updated 2 years ago
• 11chrisadams11 / Klipper-WS281x_LED_Status
  Use WS281x LED strips with Klipper
  ☆58Updated 2 years ago
• dmbutyugin / klipper
  Klipper is a 3d-printer firmware
  ☆79Updated this week
• pavluchenkor / iDryer-Unit
  Project has been in active development since October, 2024 Discord https://discord.gg/jGce5eeHHz
  ☆117Updated last week
• cdedwards / TetraFlow_MMU
  Tetra Flow MMU (multi material unit) for 3d printers
  ☆17Updated 2 years ago
• irebane / my-printers-misc
  My Klipper configs
  ☆32Updated last year
• voidtrance / voron-klipper-extensions
  A set of Klipper extensions designed to improve operation of Voron printers.
  ☆126Updated last month
• pavluchenkor / iDryerController
  ☆58Updated 6 months ago
• cryoz / K1_tenso_manual
  ☆43Updated last year
• jniebuhr / adxl345-probe
  ☆95Updated last year
• MRX8024 / chopper-resonance-tuner
  Registers calibration script for TMC drivers
  ☆249Updated 2 weeks ago
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆49Updated 3 months ago