Alternatives and similar repositories for klipper-config:

Users that are interested in klipper-config are comparing it to the libraries listed below

• dmitry-sorkin / k3d-minifeeder
  Miniature LGX Lite - compatible 3D printer feeder
  ☆27Updated 2 years ago
• CODeRUS / klipper_config
  ☆28Updated last year
• silver-alx / sbc
  Popular SBC linux images
  ☆28Updated 3 months ago
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆102Updated 2 years ago
• Tombraider2006 / K1
  creality k1 helpfull manuals for user. config, mods, hacks
  ☆137Updated this week
• pavluchenkor / iDryerController
  ☆44Updated last week
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆245Updated 2 years ago
• dmitry-sorkin / BeMeGe
  BeMeGe extruder is BMG reverse, optimized for 3d printing
  ☆59Updated last year
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• Sergey1560 / fb4s_howto
  Howto
  ☆77Updated last year
• condottab / Roborock-CPAP
  CPAP cooling system using a Roborock fan
  ☆96Updated last year
• cryoz / K1_tenso_manual
  ☆30Updated 11 months ago
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆21Updated last year
• Chiffa-C3 / Shark-Extruder
  Экструдер разработанный для замены стандартного на принтере FBG6
  ☆24Updated 2 years ago
• FBGhost-community / Marlin
  Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin inst…
  ☆13Updated 3 years ago
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆35Updated last year
• willngton / 3DPrinterConfig
  My 3D Printers Configuration backup - Marlin and Klipper
  ☆44Updated 2 years ago
• dmitry-sorkin / K3D-VOSTOK
  K3D VOSTOK 3D printer
  ☆240Updated 2 years ago
• K1-Klipper / installer_script_k1_and_max
  ☆54Updated 11 months ago
• tlace17 / K1-Flanged-Bearing-Project
  D3D community based K1 and K1 Max Gantry Mod
  ☆36Updated last year
• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆86Updated last year
• dmitry-sorkin / k3d-accuracy-test
  FDM 3D Print accuracy test
  ☆29Updated 2 years ago
• fbeltrao-br / mksts35
  ☆72Updated last year
• Vassssko / Voron-2.4-HV-electronic-compartment-mod
  Voron 2.4 clamps set to put many more things into the electronics compartment comparing to baseline.
  ☆18Updated 3 years ago
• CODeRUS / klipper_extras
  Extras
  ☆18Updated last year
• pellcorp / creality
  ☆65Updated last week
• stas2z / orange-pi-images
  Prebuilt orange pi images for selected boards with separate FAT boot partition
  ☆12Updated last year
• ArtificalSUN / MKS-WIFI_PS_uploader
  Simple G-code file uploader for 3D-printers equipped with MKS-WIFI module
  ☆56Updated 2 years ago
• goopypanther / klipper_network_status
  Klipper plugin to make system IP/etc available to macros
  ☆59Updated last year
• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆99Updated last month