Alternatives and similar repositories for PETCTL

Users that are interested in PETCTL are comparing it to the libraries listed below

• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆99Updated 2 months ago
• Sergey1560 / fb4s_howto
  Howto
  ☆77Updated last year
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆103Updated 2 years ago
• CODeRUS / klipper_config
  ☆28Updated last year
• dmitry-sorkin / BeMeGe
  BeMeGe extruder is BMG reverse, optimized for 3d printing
  ☆60Updated last year
• Sergey1560 / Marlin_FB4S
  Marlin 2.0 for Flying Bear 4S/5
  ☆226Updated last year
• dmitry-sorkin / K3D-VOSTOK
  K3D VOSTOK 3D printer
  ☆241Updated 3 weeks ago
• Tombraider2006 / K1
  creality k1 helpfull manuals for user. config, mods, hacks
  ☆145Updated this week
• silver-alx / sbc
  Popular SBC linux images
  ☆28Updated 4 months ago
• dmitry-sorkin / Marlin_FB5_K3D
  Marlin 2.0 for Flying Bear 4S
  ☆51Updated 3 years ago
• ArtificalSUN / MKS-WIFI_PS_uploader
  Simple G-code file uploader for 3D-printers equipped with MKS-WIFI module
  ☆56Updated 2 years ago
• dmitry-sorkin / k3d-accuracy-test
  FDM 3D Print accuracy test
  ☆29Updated 3 years ago
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆250Updated 3 years ago
• pavluchenkor / iDryerController
  ☆45Updated last month
• PrintMakerLab / mks-wifi-plugin
  MKS wifi plugin for Cura
  ☆142Updated last year
• xreef / MKS_WIFI_upgrade_with_BeePrint_web_interface
  Firmware for MKS WiFi module from Makerbase with BeePrint Web Interface, tested with Flying Bear Ghost 4/5/6 Reborn Flsun
  ☆73Updated 7 months ago
• makerbase-mks / MKS-WIFI
  MKS TFT WIFI and MKS ROBIN WIFI , share the same firmware. Support MKS Robin series board and MKS TFT series board, for cloud printing an…
  ☆97Updated 3 years ago
• AlexanderPro29 / OctoPrint-RU-LangPack
  RUssian LangPack for OctoPrint
  ☆19Updated last year
• evgs / FBG6-Klipper
  ☆16Updated 3 weeks ago
• VICLER / GyverDrink
  Наливатор на Arduino
  ☆40Updated 3 years ago
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• vladimir-poleh / klipper-config
  ☆10Updated last year
• gknapp / ghost6
  FlyingBear Ghost 6 3D Printer notes
  ☆17Updated 9 months ago
• dmitry-sorkin / k3d-minifeeder
  Miniature LGX Lite - compatible 3D printer feeder
  ☆27Updated 2 years ago
• gotchau / GBot-Tiny-Mark-II
  ☆32Updated 5 months ago
• FBGhost-community / Marlin
  Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin inst…
  ☆13Updated 3 years ago
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆21Updated 2 years ago
• Ryoko / DeepKarasR
  FlyingBear Ghost 6 BIQU H2 Head
  ☆11Updated 2 years ago
• Chiffa-C3 / Shark-Extruder
  Экструдер разработанный для замены стандартного на принтере FBG6
  ☆25Updated 2 years ago
• evgs / kross-pi-hat
  RPI/OPI Hat board for FB Ghost6 and Reborn2 touchscreens
  ☆16Updated last month