Alternatives and similar repositories for orange-pi-images:

Users that are interested in orange-pi-images are comparing it to the libraries listed below

• silver-alx / sbc
  Popular SBC linux images
  ☆28Updated 2 months ago
• CODeRUS / klipper_config
  ☆28Updated last year
• CODeRUS / klipper_extras
  Extras
  ☆18Updated last year
• pavluchenkor / iDryerController
  ☆41Updated 3 months ago
• condottab / Roborock-CPAP
  CPAP cooling system using a Roborock fan
  ☆95Updated last year
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆21Updated last year
• altzbox / Chopper-tuning-guide
  ☆27Updated last year
• dmitry-sorkin / k3d-minifeeder
  Miniature LGX Lite - compatible 3D printer feeder
  ☆27Updated 2 years ago
• D3vil-Design / K1-Max-Manta-Conversion
  ☆21Updated 7 months ago
• droans / klipper_extras
  Custom Extras for Klipper
  ☆36Updated 2 years ago
• CODeRUS / klipper_web_builder
  Simple Klipper Firmware Builder
  ☆14Updated last year
• worksasintended / klipper_linear_movement_analysis
  ☆73Updated last year
• goopypanther / klipper_network_status
  Klipper plugin to make system IP/etc available to macros
  ☆60Updated last year
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• bigtreetech / K-Touch
  Repository for the BIGTREETECH K-Touch
  ☆25Updated 2 months ago
• tlace17 / K1-Flanged-Bearing-Project
  D3D community based K1 and K1 Max Gantry Mod
  ☆32Updated last year
• cryoz / K1_tenso_manual
  ☆28Updated 10 months ago
• Vassssko / Voron-2.4-HV-electronic-compartment-mod
  Voron 2.4 clamps set to put many more things into the electronics compartment comparing to baseline.
  ☆18Updated 3 years ago
• ripinteer / fan_protector
  Simple polulu-compatible protection board for Xiaomi/Roborock radial fans
  ☆18Updated last year
• bigtreetech / TFT35-SPI
  ☆58Updated 10 months ago
• zztopper / voron_v2.4_1030
  Voron v2.4 #1030 300x300 config repo
  ☆31Updated this week
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆101Updated 2 years ago
• nhchiu / 3DPrinter-Designs
  Collection of miscellaneous parts and upgrades for 3D printers.
  ☆18Updated 7 months ago
• bigtreetech / CB2
  The official repo for the BTT Pi2 and CB2
  ☆90Updated this week
• K1-Klipper / installer_script_k1_and_max
  ☆53Updated 9 months ago
• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆85Updated last year
• vladimir-poleh / klipper-config
  ☆10Updated last year
• OpenAMSOrg / filament-buffer
  OpenAMS Filament Buffer
  ☆45Updated last month
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆31Updated last year
• Lzhikai / siboor-voron
  Machine technical specification
  ☆20Updated last year