Alternatives and similar repositories for sbc

Users that are interested in sbc are comparing it to the libraries listed below

• CODeRUS / klipper_config
  ☆28Updated last year
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆104Updated 3 years ago
• CODeRUS / klipper_extras
  Extras
  ☆19Updated 2 months ago
• Sergey1560 / fb4s_howto
  Howto
  ☆80Updated 2 years ago
• pavluchenkor / iDryerController
  ☆57Updated 4 months ago
• Tombraider2006 / K1
  creality k1 helpfull manuals for user. config, mods, hacks
  ☆220Updated 2 months ago
• stas2z / orange-pi-images
  Prebuilt orange pi images for selected boards with separate FAT boot partition
  ☆16Updated 2 years ago
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆259Updated 3 years ago
• cryoz / K1_tenso_manual
  ☆38Updated last year
• vladimir-poleh / klipper-config
  ☆10Updated 2 years ago
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• makerbase-mks / MKS-SKIPR
  MKS SKIPR is an all-in-one board launched by Makerbase for running Klipper. It integrates the RK3328 SOC running the Klipper host and the…
  ☆122Updated 3 years ago
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆24Updated 4 months ago
• dmitry-sorkin / K3D-VOSTOK
  K3D VOSTOK 3D printer
  ☆243Updated 7 months ago
• condottab / Roborock-CPAP
  CPAP cooling system using a Roborock fan
  ☆106Updated 2 years ago
• kemsky / creality-k1-max-xy-rails-mod
  Creality K1 Max XY Rails Mod
  ☆37Updated 6 months ago
• willngton / 3DPrinterConfig
  My 3D Printers Configuration backup - Marlin and Klipper
  ☆48Updated 3 years ago
• Vassssko / Voron-2.4-HV-electronic-compartment-mod
  Voron 2.4 clamps set to put many more things into the electronics compartment comparing to baseline.
  ☆19Updated 3 years ago
• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆100Updated last month
• K1-Klipper / installer_script_k1_and_max
  ☆58Updated last year
• fbeltrao-br / mksts35
  ☆80Updated 2 years ago
• Yumi-Lab / YUMI_PLR
  Power loss recovery for klipper
  ☆40Updated last year
• cdedwards / TetraFlow_MMU
  Tetra Flow MMU (multi material unit) for 3d printers
  ☆17Updated last year
• deflord / 3def
  Files and configuration
  ☆53Updated last week
• tlace17 / K1-Flanged-Bearing-Project
  D3D community based K1 and K1 Max Gantry Mod
  ☆49Updated 2 years ago
• altzbox / Chopper-tuning-guide
  ☆27Updated last year
• redrathnure / armbian-mkspi
  Armbian Linux Build Framework
  ☆139Updated 2 months ago
• evgs / kross-pi-hat
  RPI/OPI Hat board for FB Ghost6 and Reborn2 touchscreens
  ☆17Updated 8 months ago
• ballaswag / k1-discovery
  Self discovered technical details for the Creality K1 printer
  ☆43Updated 2 years ago
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆47Updated 2 months ago