Alternatives and similar repositories for MPRT

Users that are interested in MPRT are comparing it to the libraries listed below

• cinderblock / 3-Phase-Driver
  Hardware design for a 3 Phase BLDC controller
  ☆57Updated 5 years ago
• MarginallyClever / sixi-2
  Sixi 2 Robot Arm
  ☆34Updated 3 years ago
• openpnp / mica-feeder
  Automatic SMT Tape Feeder by Pham Thang
  ☆19Updated 7 years ago
• avtehnik / gt2-gear-genaretor
  ☆37Updated 2 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆77Updated 4 years ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• ultimachine / Archim
  The 32-bit next generation of RAMBo
  ☆24Updated 5 years ago
• sequoia-hope / open_linear_motor
  Design files for a brushless linear motor project I worked on mostly from 2010-2012
  ☆27Updated 4 years ago
• bfoz / Ester
  Ester 3D Laser Printer
  ☆39Updated last year
• benbreen / Cycloidal
  Cycloidal Gear Generator for Fusion 360
  ☆24Updated 9 years ago
• makerbase-mks / MKS-SERVO57B
  MKS SERVO57B is 3d printer closed loop stepper motor NEMA23 MKS SERVO57 developed by Makerbase that prevents losing steps. CPU is STM32F1…
  ☆22Updated 3 years ago
• PRouzeau / OpenSCAD-Delta-Simulator
  Simulate cinematic of a delta robot (3D printer or CNC) - Animation
  ☆72Updated 4 years ago
• tapnair / Fusion360HypocycloidGear
  Script to generate Hypocycloid Gears Sketch
  ☆25Updated 10 years ago
• BETZtechnik / ICEpick--Direct-drive-pick-and-place-head
  Pick and Place head with dual nozzles
  ☆39Updated 5 years ago
• zelogik / AluXY
  A ful metal CoreXY system for 3D printer, mill etc..
  ☆47Updated 11 years ago
• xpix / XDisPlace
  XDisplace are a complete solution to mill, dispense solder paste and pixk and place components to a pcb in one process!
  ☆12Updated 8 years ago
• bobricius / 2.5D-stepper-motor
  It is compatible with standard stepper motor diver, cnc or GRBL shield, direct replacement of X-Y stepper motors.
  ☆27Updated 6 years ago
• grblHAL / Simulator
  grblHAL drivers for simulation (Linux and Windows)
  ☆31Updated last week
• gnea / grbl-LPC
  ☆74Updated 3 years ago
• ShaukiBagdadi / rUka-Robot-Arm
  Low Part Count Robot Arm
  ☆12Updated 7 years ago
• bobricius / mbot
  2D actuator
  ☆28Updated 6 years ago
• uStepper / uStepperS
  ☆54Updated last year
• SG-O / MiniFeedPCB
  Main PCB for automated SMT Feeder
  ☆10Updated 4 years ago
• ChrisWag91 / PI-LCNC
  Adapter board to use a Raspberry Pi as a Linux CNC controller
  ☆58Updated 2 years ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆36Updated last year
• SebG3D / TapePuller
  tape puller/remover for 0816 automatic feeder
  ☆21Updated 5 years ago
• paulusjacobus / SuperGerbil
  STM32 driven ARM Grbl firmware
  ☆23Updated 5 years ago
• Peter-van-Tol / LITEXCNC-HUB75HAT
  A PCB that turns the Colorlight 5A-75B into an easy to use LinuxCNC motion controller
  ☆11Updated last year
• xpix / XATC
  DIY CNC Automatic Toolchanger
  ☆66Updated 6 years ago
• Scavenger18 / RepoPNP
  Files concering PAIND PNP Feeder
  ☆23Updated 7 years ago