Alternatives and similar repositories for external_stepper_motor_driver

Users that are interested in external_stepper_motor_driver are comparing it to the libraries listed below

• dining-philosopher / litefeeder
  Semi-automatic passive printable/castable feeder for LitePlacer
  ☆59Updated 5 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆79Updated 4 years ago
• terjeio / CNC_Breakout_Nucleo64
  CNC breakout for STM324F411 and ST32F446 development boards
  ☆21Updated 2 years ago
• Patrick-E-Rankin / Mach3Controller
  Android / ESP32 / ESP8266 Controller (+ coordinate display) for Mach3 CNC
  ☆21Updated 4 years ago
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆34Updated 3 years ago
• kingoflolz / linear-actuator-hardware
  ☆63Updated 3 years ago
• tenbaht / servo-motor-controller
  Porting the great SMC3 servo motor controller by Elm Chan to an ATmega328
  ☆17Updated 6 years ago
• ErichStyger / McuOpenPnP_Machine
  Repository for the McuOnEclipse OpenPnP machine
  ☆65Updated 4 years ago
• Laser4DIY / Laser-Driver-v2
  MCU-based multipurpose Laser Diode driver
  ☆19Updated 4 years ago
• Scavenger18 / RepoPNP
  Files concering PAIND PNP Feeder
  ☆23Updated 7 years ago
• paulusjacobus / SuperGerbil
  STM32 driven ARM Grbl firmware
  ☆23Updated 5 years ago
• kingoflolz / linear-actuator-firmware
  ☆29Updated 3 years ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆35Updated 10 months ago
• reivax-boucoi / Electronic_Load
  DIY Electronic load for DCDC converter characterization
  ☆50Updated 4 years ago
• cinderblock / 3-Phase-Controller
  Firmware for 3 Phase BLDC controller
  ☆41Updated 5 years ago
• SebG3D / TapePuller
  tape puller/remover for 0816 automatic feeder
  ☆21Updated 6 years ago
• richardklingler / openpnp
  My pick and place machine controlled by the great OpenPNP software.
  ☆76Updated 4 years ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 5 months ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆28Updated 3 months ago
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆77Updated 3 weeks ago
• ottoragam / Tarocco
  Closed Loop Motor Controller
  ☆134Updated 4 years ago
• SupaCoder / 0816-Lumen-SMT-Feeder-Remix
  0816 SMT Automatic Feeder modified to work with the OpuloPNP. Custom firmware written for an arduino nano with a servo sheild can run 12 …
  ☆15Updated 3 years ago
• makerstorage / pnpAssist
  PNPASSIST: A “SMART” BUILD PLATFORM FOR MANUAL PCB ASSEMBLY
  ☆43Updated 3 years ago
• coreWeaver / LC-Meter
  Open Source LC-Meter. All documentation included.
  ☆84Updated 3 years ago
• hasenbanck / heteromycin
  A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC
  ☆39Updated 5 years ago
• opengalvo / OPAL
  Minimalistic FW for Processing GCode to Galvanometer signals
  ☆99Updated 10 months ago
• tom-biskupic / LabPSU
  Open Source Lab Power Supply
  ☆28Updated 3 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆119Updated last week
• dronecz / ESP32-Reflow-Controller
  Reflow controller with ESP32 and TFT LCD on board.
  ☆68Updated 2 months ago
• markmaker / PushPullFeeder
  All 3d-Printed Tape&Reel Feeder
  ☆79Updated 9 months ago