Alternatives and similar repositories for open_linear_motor

Users that are interested in open_linear_motor are comparing it to the libraries listed below

• kingoflolz / linear-actuator-hardware
  ☆64Updated 3 years ago
• roboterclubaachen / micro-motor
  µMotor miniature motor controller
  ☆41Updated 6 months ago
• kingoflolz / linear-actuator-firmware
  ☆29Updated 3 years ago
• VIPQualityPost / lemon-pepper-stepper
  simplefoc all-in-one 50W hybrid stepper + bldc driver
  ☆51Updated last year
• qwertpas / O32controller
  Miniature closed-loop controller for brushless DC motors
  ☆29Updated last year
• Igitigit2 / SimpleCanLib
  CAN bus library for ESP32 and STM32 G431
  ☆32Updated last year
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆71Updated 5 months ago
• bobricius / 2.5D-stepper-motor
  It is compatible with standard stepper motor diver, cnc or GRBL shield, direct replacement of X-Y stepper motors.
  ☆28Updated 6 years ago
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆115Updated 3 years ago
• PCrnjak / S-Drive-Firmware
  S_Drive is small bldc driver based on L6234 Three phase motor driver.
  ☆43Updated last year
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated 2 years ago
• hstarmans / hexastorm
  Amaranth HDL framework for laser scanner with motion control
  ☆30Updated last week
• ghent360 / PrntrBoardV2
  32-bit 3D Printer controller board using STM32F407 and replaceable TMC2660/2209 stepper drivers.
  ☆43Updated 3 years ago
• atomic14 / kicad-coil-plugins
  Some simple plugins for generating stator coils in kicad
  ☆105Updated last year
• benbreen / Cycloidal
  Cycloidal Gear Generator for Fusion 360
  ☆24Updated 9 years ago
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆31Updated 7 months ago
• opulo-inc / paste-extruder
  Paste extruder head for the LumenPnP
  ☆44Updated last week
• ExcessiveMotion / drive-hardware
  ☆35Updated 2 weeks ago
• cmore839 / DIY-Linear-Motor
  ☆40Updated last year
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆37Updated 11 months ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• lucysrausch / ottercontrol
  Hardware files for OtterControl BLDC motor controller
  ☆65Updated 5 years ago
• microsmt / Microsmt-PNP-hardware
  All documents about making microsmt pnpboard
  ☆57Updated last week
• ottoragam / Tarocco
  Closed Loop Motor Controller
  ☆134Updated 4 years ago
• multigcs / riocore
  riocore
  ☆55Updated this week
• naoanya / bldc
  ☆20Updated 6 months ago
• owennewo / simplefoc_skateboard_g431b
  ☆30Updated 4 years ago
• freakontrol / stmbl
  ☆33Updated last month
• hasenbanck / heteromycin
  A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC
  ☆39Updated 5 years ago
• NiklasHammerstone / GalvoStep
  Project for building a cheap galvo laser system using Stepper motors and widely available parts.
  ☆56Updated last year