Alternatives and similar repositories for CNC_Breakout_Nucleo64

Users that are interested in CNC_Breakout_Nucleo64 are comparing it to the libraries listed below

• avizienis / Minimal-Black-Pill--STM32F4xx-BOB-for-grblHAL
  Single layer breakout board for the popular Black Pill. Features 4 axes, 5V outputs, optoisolated inputs.
  ☆12Updated 4 years ago
• grblHAL / STM32F1xx
  grblHAL driver for ST STM32F1xx (Redpill, Bluepill)
  ☆58Updated this week
• paulusjacobus / SuperGerbil
  STM32 driven ARM Grbl firmware
  ☆23Updated 5 years ago
• jarekkt / step2mach
  Plugin for Mach3 and Nucleo-F429ZI board
  ☆17Updated 5 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆78Updated 4 years ago
• Alfrederson / cncstm32
  CNC Base for Blue Pill
  ☆17Updated 6 years ago
• ryannining / karyacontroller
  4 axis CNC, 3D, Laser Controller
  ☆61Updated 8 months ago
• buildbotics / bbctrl-pcb
  Buildbotics CNC, 3D printer and other machine controller
  ☆49Updated 3 years ago
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆34Updated 2 years ago
• pekkaroi / ethernetcnc
  ☆14Updated 6 years ago
• ottoragam / Tarocco
  Closed Loop Motor Controller
  ☆134Updated 4 years ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 5 months ago
• makerbase-mks / MKS-SERVO57B
  MKS SERVO57B is 3d printer closed loop stepper motor NEMA23 MKS SERVO57 developed by Makerbase that prevents losing steps. CPU is STM32F1…
  ☆22Updated 3 years ago
• technosar / GRBL_STM32
  An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on a straight ST…
  ☆29Updated 4 years ago
• mstrens / grbl_controller_stm32
  Grbl controller running on stm32F103
  ☆37Updated 6 years ago
• grblHAL / STM32F4xx
  grblHAL driver for ST STM32F4xx (Nucleo-64, Blackpill)
  ☆116Updated this week
• pvico / grbl32
  CNC controller running on the STM32F103 "Blue Pill" board, build and flash on Mac/Linux
  ☆65Updated 3 years ago
• dungjk / grbl-stm32
  An open source, embedded, high performance g-code-parser and CNC milling controller. This is a port of GRBL 1.1 to STM32F10X target.
  ☆82Updated 3 years ago
• tenbaht / servo-motor-controller
  Porting the great SMC3 servo motor controller by Elm Chan to an ATmega328
  ☆17Updated 6 years ago
• hasenbanck / heteromycin
  A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC
  ☆39Updated 5 years ago
• martinribelotta / h730duino
  STM32H7 Arduino form factor and software compatible board
  ☆32Updated 3 years ago
• bdring / 4_Axis_SPI_CNC
  4 Axis CNC Controller for Grbl_ESP32
  ☆66Updated 5 years ago
• uStepper / uStepperS
  ☆54Updated last year
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 8 years ago
• SebG3D / TapePuller
  tape puller/remover for 0816 automatic feeder
  ☆21Updated 6 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆118Updated last year
• openpnp / mica-feeder
  Automatic SMT Tape Feeder by Pham Thang
  ☆20Updated 8 years ago
• langwadt / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆33Updated 4 years ago
• monolithicpower / MagAlpha-Arduino-Library
  Arduino library for the MPS MagAlpha magnetic angle sensor.
  ☆23Updated last month
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆76Updated last year