Alternatives and similar repositories for RemoteDSM

Users that are interested in RemoteDSM are comparing it to the libraries listed below

• KoshiroRobot / Simple-Smart-Servo-Driver
  ☆47Updated last year
• Shortcircuitboards / PCB-CNC
  DIY Printed small PCB CNC for fast Prototyping
  ☆57Updated 4 years ago
• drandrewthomas / ESP32_GRBL_CNC_Wireless_Pendant
  A wireless GRBL CNC pendant project based on the ESP32 micro-controller
  ☆54Updated 4 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆61Updated last month
• roTechnic / CycloidalDesign
  ☆24Updated 3 years ago
• nickrehm / dRehmFlight-LandSpeeder
  Modified version of original dRehmFlight VTOL for the flying RC drift car
  ☆35Updated last year
• TheDIYGuy999 / Micro_RC_Receiver
  An Atmega328P based 2.4GHz receiver with integrated TB6612FNG motor driver. PWM and SBUS outputs.
  ☆152Updated last year
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆81Updated 5 months ago
• SasaKaranovic / DIY-Camera-Slider
  DIY WiFi Enabled Camera Slider using ESP32
  ☆125Updated 11 months ago
• Neumi / tmc2209_devboard
  An Arduino shield to test the TMC2209 stepper motion controller by Trinamic.
  ☆37Updated 2 years ago
• atomic14 / esp32-laser-show
  ☆85Updated 2 years ago
• Rack-Robotics / Powercore-V1.0-Manual
  Theory and operation of the Powercore V1 EDM PSU
  ☆47Updated 2 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆80Updated 5 years ago
• TGit-Tech / GRBL-28byj-48
  Grbl ver 1.1f.20170131 with XYZ Unipolar Stepper Support (28byj-48)
  ☆135Updated 5 years ago
• positron96 / cnc3018-offline-controller
  Open-source firmware for popular cnc3018 stm32-based offline controller
  ☆79Updated last year
• bdring / Grbl_ESP32_MPCNC_Controller
  A Grbl_ESP32CNC Controller for MPCNC
  ☆90Updated 3 years ago
• EmanuelBender / HEX_POD
  Multi-sensor intelligent environmental Monitor
  ☆18Updated last year
• DDeGonge / MultiUseBoard
  The MUB - An ultra-compact, modular processing unit
  ☆63Updated 3 years ago
• frank26080115 / Hydra-Dual-Brushed-Motor-ESC
  Dual brushed motor ESC firmware compatible with brushless motor ESCs
  ☆33Updated last year
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆88Updated 5 months ago
• XRobots / WiperMotorServo
  ☆48Updated 7 years ago
• bmellink / IBusBM
  Arduino library for RC IBUS protocol - servo (receive) and sensors/telemetry (send) using hardware UART
  ☆226Updated last year
• digitalbird01 / DigitalBird-Camera-Slider
  Professional level DIY Camera Motion Control System
  ☆108Updated 3 months ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆64Updated 2 years ago
• DzikuVx / camera_slider
  ☆20Updated 2 years ago
• EricYufengWu / q8bot
  Q8 Robot
  ☆192Updated last week
• TRD-B / Lizard
  3D printed RC race car with custom electronics
  ☆104Updated 5 months ago
• XRobots / ROSremote
  ☆35Updated 3 years ago
• MGX3D / EspDRO
  ESP32 DIY Digital Readout
  ☆109Updated 6 years ago
• MakingStuffChannel / DigitalCalipers
  Source code and other files for reading values from digital calipers. See the project page for complete write up at http://makingstuff.in…
  ☆40Updated 9 years ago