Alternatives and similar repositories for probe-screen-ng:

Users that are interested in probe-screen-ng are comparing it to the libraries listed below

• verser-git / probe_screen_v2
  ☆43Updated 4 years ago
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆72Updated this week
• ntc490 / fusion360
  Convert Fusion360 Tool Library to LinuxCNC Tool Table
  ☆32Updated 2 years ago
• kcjengr / probe_basic
  User interface for the LinuxCNC machine control.
  ☆98Updated 3 weeks ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆88Updated last week
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆145Updated 2 months ago
• TooTall18T / tool_length_probe
  Tool length probe subroutine for Probe Basic.
  ☆17Updated last week
• joco-nz / bf20_mill
  QtPyVCP based GUI for Linuxcnc
  ☆12Updated last year
• GuiHue / probe_screen_v2
  ☆10Updated 5 years ago
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆43Updated 2 months ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆29Updated 5 months ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆20Updated 9 months ago
• linuxcnc-ethercat / linuxcnc-ethercat
  LinuxCNC EtherCAT HAL driver
  ☆46Updated last week
• FernV / NativeCAM
  NativeCAM for LinuxCNC embeds in axis or gmoccapy interfaces
  ☆47Updated 4 years ago
• jethornton / mesact1
  ☆24Updated last year
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• bartei / rotary-controller-f4
  Digital Read Out and Single Axis Controller
  ☆43Updated 7 months ago
• GuiHue / myfenjalinuxcnc
  Repository for my LinuxCNC Config for a CNC Router based on the FENJA Design
  ☆20Updated last year
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆59Updated last year
• hausen8 / EasyProbe
  Easy to install and easy to use probe panel for LinuxCNC Axis GUI
  ☆14Updated 9 months ago
• G-EDM / G-EDM-v1-deprecated
  The G-EDM is a 4in1 electrical discharge machine that supports sinker EDM, EDM engraving, EDM drilling and Wire EDM operations. In the fu…
  ☆49Updated 6 months ago
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆33Updated last year
• jschoch / ESPels
  ESP32 electronic leadscrew for a lathe
  ☆23Updated 5 months ago
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆47Updated last week
• arsi-apli / BLDC_Klipper_doc
  This is documentation for a modified version of the Klipper firmware that allows you to directly drive a BLDC Motor in an open loop confi…
  ☆18Updated 2 years ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆61Updated last month
• IvDm / Z-probe-on-smd-resistors-2512
  Auto bed level strain gage for 3D printer using resistors 2512 instead of strain gauges.
  ☆137Updated 4 years ago
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆26Updated last month
• cnc-club / linuxcnc-features
  LinuxCNC Features
  ☆57Updated 9 years ago
• fdarling / mesa-smartserial-device-template
  Mesa SmartSerial (SSLBP) custom device template project
  ☆11Updated 4 years ago