Alternatives and similar repositories for JauriaCNC:

Users that are interested in JauriaCNC are comparing it to the libraries listed below

• joco-nz / bf20_mill
  QtPyVCP based GUI for Linuxcnc
  ☆12Updated last year
• MachineryScience / Rockhopper
  Machinery Science LinuxCNC remote access, configuration and utilities
  ☆17Updated 6 years ago
• linuxcnc-probe-screen / probe-screen-ng
  LinuxCNC Probe Screen
  ☆25Updated last year
• Deotti-cl / linuxcnc-esp32
  External pulse generator
  ☆17Updated 3 years ago
• cnc-club / linuxcnc-engraving-comp
  Component for engraving non flat surfaces using LinuxCNC
  ☆15Updated 10 years ago
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• LinuxCNC / mesaflash
  Configuration and diagnostic tool for Mesa Electronics PCI(E)/ETH/EPP/USB/SPI boards
  ☆36Updated last week
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆19Updated 8 months ago
• fdarling / mesa-smartserial-device-template
  Mesa SmartSerial (SSLBP) custom device template project
  ☆11Updated 4 years ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆27Updated 4 months ago
• cnc-club / linuxcnc-features
  LinuxCNC Features
  ☆57Updated 9 years ago
• FernV / NativeCAM
  NativeCAM for LinuxCNC embeds in axis or gmoccapy interfaces
  ☆47Updated 4 years ago
• cdsteinkuehler / bobc_hardware
  CRAMPS - A Cape version of the RAMPS-FD design for 3D printing
  ☆45Updated 5 years ago
• futurelink / linuxcnc-spindle-encoder
  A small AVR controller and a component to connect high precision encoder to LinuxCNC via Modbus RTU
  ☆18Updated 5 years ago
• verser-git / probe_screen_v2
  ☆43Updated 4 years ago
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆70Updated 2 weeks ago
• KurtJacobson / hazzy
  Touchscreen UI for LinuxCNC
  ☆32Updated 4 years ago
• jethornton / mill_touch_v6
  QtPyVCP Mill Touch Screen
  ☆13Updated 3 years ago
• LinuxCNC / hostmot2-firmware
  HostMot2 FPGA firmware
  ☆20Updated 3 years ago
• pekkaroi / ethernetcnc
  ☆14Updated 6 years ago
• jethornton / flexgui
  A flexible GUI for LinuxCNC
  ☆16Updated this week
• hasenbanck / heteromycin
  A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC
  ☆38Updated 4 years ago
• jethornton / mesact1
  ☆24Updated last year
• imrahil / smoothieware-webui
  Better webUI for Smoothieware
  ☆21Updated 8 years ago
• buildbotics / bbctrl-firmware
  Buildbotics CNC Controller Firmware
  ☆69Updated last week
• multigcs / riocore
  riocore
  ☆30Updated this week
• intelligent-agent / redeem
  Firmware for Replicape
  ☆36Updated 2 years ago
• TooTall18T / tool_length_probe
  Tool length probe subroutine for Probe Basic.
  ☆17Updated this week
• scottalford75 / LinuxCNC-3D-Printing
  ☆25Updated last year
• openpnp / mica-feeder
  Automatic SMT Tape Feeder by Pham Thang
  ☆19Updated 7 years ago