Alternatives and similar repositories for mesact1:

Users that are interested in mesact1 are comparing it to the libraries listed below

• joco-nz / bf20_mill
  QtPyVCP based GUI for Linuxcnc
  ☆12Updated last year
• linuxcnc-probe-screen / probe-screen-ng
  LinuxCNC Probe Screen
  ☆25Updated last year
• verser-git / probe_screen_v2
  ☆43Updated 4 years ago
• grblHAL / plugins
  Plugins overview
  ☆25Updated 2 months ago
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆42Updated last month
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆67Updated last week
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆55Updated last year
• kentavv / electronic-leadscrew
  Lathe electronic leadscrew controller
  ☆15Updated 4 years ago
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 4 years ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆19Updated 8 months ago
• RootCNC / Root-Controller-ISO
  ESP32 GRBL Controller for the Root CNC machines
  ☆22Updated last year
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆26Updated 9 months ago
• cnc-club / linuxcnc-engraving-comp
  Component for engraving non flat surfaces using LinuxCNC
  ☆15Updated 9 years ago
• FernV / NativeCAM
  NativeCAM for LinuxCNC embeds in axis or gmoccapy interfaces
  ☆47Updated 4 years ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆141Updated last week
• raenji-sk / grblHAL_Fusion360_Post_Processor
  Experimental grblHAL post processor with canned cycles and 4th axis support
  ☆16Updated 11 months ago
• G-EDM / G-EDM-v1-deprecated
  The G-EDM is a 4in1 electrical discharge machine that supports sinker EDM, EDM engraving, EDM drilling and Wire EDM operations. In the fu…
  ☆47Updated 5 months ago
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆46Updated last year
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆27Updated 3 months ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆39Updated last month
• verser-git / probe_screen
  Probe Screen for LinuxCNC
  ☆21Updated 6 years ago
• jschoch / ESPels
  ESP32 electronic leadscrew for a lathe
  ☆21Updated 3 months ago
• scottalford75 / LinuxCNC-3D-Printing
  ☆25Updated last year
• grblHAL / iMXRT1062
  grblHAL driver for NXP iMXRT1062 (Teensy 4.x)
  ☆51Updated this week
• kcjengr / probe_basic
  User interface for the LinuxCNC machine control.
  ☆96Updated this week
• Alfrederson / cncstm32
  CNC Base for Blue Pill
  ☆16Updated 5 years ago
• grblHAL / drivers
  Driver overview
  ☆32Updated this week
• Expatria-Technologies / grblhal_2000_PrintNC
  Expatria Technologies GRBLHAL Breakout board for PrintNC
  ☆28Updated last year
• scottalford75 / Remora-NVEM
  Remora firmware for Novusun NVEM controller board
  ☆14Updated 2 months ago
• TurBoss / JauriaCNC
  Minimial featured linuxcnc interface
  ☆9Updated last year