Alternatives and similar repositories for Mini_Excavator:

Users that are interested in Mini_Excavator are comparing it to the libraries listed below

• fiberpunk1 / Beam-ESP32
  Beam by Fiberpunk - ESP32
  ☆70Updated last year
• FYSETC / FYSETC-E4
  FYSETC Board - The E4 board is a minimal 3D printer control board based on the ESP32 microcontroller from ESPRESSIF, with built-in Wi-Fi …
  ☆61Updated last year
• luc-github / ESP3DLib
  ESP3D library for Marlin and ESP32 boards
  ☆105Updated last month
• makerbase-mks / MKS-MINI12864-V3
  ☆46Updated 3 years ago
• yyh1002 / DXU
  ☆55Updated 4 years ago
• luc-github / ESP3D-TFT
  ESP3D Firmware for ESP32 based TFT
  ☆43Updated 2 months ago
• mstrens / grbl_controller_esp32
  grbl controller for esp32
  ☆184Updated last year
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆41Updated this week
• dracir9 / 3DPrinterScreen
  ESP32 based touch screen 3d printer controller
  ☆16Updated last year
• markniu / PandaCAN
  CAN bus extruder, more resistant to noise,reduce a lot of wires for your 3D printer
  ☆114Updated last year
• ProfBoots / MiniSkidi-V3.0
  ☆39Updated 8 months ago
• seeul8er / RepPanel_ESP32
  Alternative to PanelDue. Embedded UI for Duet & RepRap based 3D printers. Running on the ESP32. Optimized for 3.5" displays. WiFi or UART…
  ☆91Updated 2 years ago
• xSnowHeadx / HollowClock
  An analog clock with flying hands controlled from internet-time via ESP8266
  ☆14Updated 2 years ago
• MGX3D / EspDRO
  ESP32 DIY Digital Readout
  ☆91Updated 5 years ago
• makerbase-mks / MKS-TinyBee
  MKS TinyBee is a mainboard for 3d printing, based on ESP32 module
  ☆131Updated 2 years ago
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆74Updated 2 years ago
• simon-jouet / ESP32Controller
  ESP32-based 3D printer controller
  ☆123Updated 3 years ago
• zapta / legacy_stepper_motor_analyzer
  A DYI minimalist hardware stepper motor analyzer with graphical touch screen.
  ☆161Updated last year
• makerbase-mks / MKS-GEN_L
  MKS GEN_L is a powerful 3D printer control board with ATMEGA2560 and compatible with RAMPS. V2.1 version the motherboard integrates SPI …
  ☆199Updated 3 years ago
• EtteGit / ERCF-easy-brd
  ☆36Updated 3 years ago
• TGit-Tech / GRBL-28byj-48
  Grbl ver 1.1f.20170131 with XYZ Unipolar Stepper Support (28byj-48)
  ☆107Updated 4 years ago
• makerbase-mks / Datasheet
  ☆72Updated 4 years ago
• ProfBoots / 3D-Printed-RC-DumpTruck-2.0
  Need to transport a pencil across your desk or perhaps a stack of sticky notes? Never fear the MiniDump is here.
  ☆16Updated last year
• Lite3DP / Lite3DP-S1
  Lite3DP S1
  ☆159Updated last year
• robaki-dev / robak
  Robak RC DIY car
  ☆140Updated last year
• zapta / simple_stepper_motor_analyzer
  A DYI stepper motor analyzer. This is a new design that is based on Raspberry Pi Pico and users a compact single PCB design. NOTE: The l…
  ☆149Updated last year
• bdring / Grbl_ESP32_MPCNC_Controller
  A Grbl_ESP32CNC Controller for MPCNC
  ☆87Updated 2 years ago
• maplerainresearch / MRR_ESPE
  MRR ESPE 3D printer control board
  ☆36Updated 5 years ago
• eponra / flatpack
  A foldable fixed-bed-cantilever 3D-printer, that fits into a spoolbox and uses off-the-shelf parts only.
  ☆165Updated last month
• makerbase-mks / MKS-Robin-Nano-V3.X
  Robin nano V3 is an upgraded version of Robin Nano V2.0. The upgrade changes are quite large, including upgrading the MCU to the M4 core,…
  ☆149Updated last year