Alternatives and similar repositories for LaserProjectorV2

Users that are interested in LaserProjectorV2 are comparing it to the libraries listed below

• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆75Updated last year
• digitalbird01 / DigitalBird-Camera-Slider
  Professional level DIY Camera Motion Control System
  ☆99Updated 3 months ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆77Updated 4 years ago
• atomic14 / esp32-laser-show
  ☆77Updated last year
• bdring / Grbl_ESP32_MPCNC_Controller
  A Grbl_ESP32CNC Controller for MPCNC
  ☆88Updated 3 years ago
• uStepper / uStepperS
  ☆54Updated last year
• opengalvo / OPAL
  Minimalistic FW for Processing GCode to Galvanometer signals
  ☆92Updated 7 months ago
• bdring / 4_Axis_SPI_CNC
  4 Axis CNC Controller for Grbl_ESP32
  ☆66Updated 5 years ago
• Neumi / tmc2209_devboard
  An Arduino shield to test the TMC2209 stepper motion controller by Trinamic.
  ☆36Updated 2 years ago
• mnesarco / HyperController
  8DOF Space Controller Device for FreeCAD
  ☆32Updated 4 years ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆61Updated 2 years ago
• obstruse / LaserDemo
  Generate test patterns for laser galvanometer
  ☆36Updated 2 years ago
• positron96 / cnc3018-offline-controller
  Open-source firmware for popular cnc3018 stm32-based offline controller
  ☆74Updated 7 months ago
• alextreseder / picoEDM
  Minimalist DIY Wire EDM for Hobbyists & Education
  ☆47Updated 5 months ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆117Updated last year
• cprezzi / grbl-LPC
  Multiple compiled versions for different boards & machines (under releases)
  ☆58Updated 3 years ago
• gnea / grbl-LPC
  ☆75Updated 3 years ago
• KoshiroRobot / Simple-Smart-Servo-Driver
  ☆40Updated 6 months ago
• HaleDesign / TorchHeightController
  Arduino based THC that read plasma cutter voltage and send Up and Down signals to Plasma Torch Actuator to adjust voltage to target value…
  ☆45Updated 4 years ago
• NiklasHammerstone / GalvoStep
  Project for building a cheap galvo laser system using Stepper motors and widely available parts.
  ☆52Updated last year
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆72Updated 4 years ago
• FYSETC / FYSETC-E4
  FYSETC Board - The E4 board is a minimal 3D printer control board based on the ESP32 microcontroller from ESPRESSIF, with built-in Wi-Fi …
  ☆67Updated 2 months ago
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆47Updated 3 months ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆36Updated last year
• bdring / Grbl_ESP32_TMC2130_Plotter_Controller
  ☆66Updated 5 years ago
• clehn8ok / DIY3AxisCameraSlider
  3D Printed 3 Axis Camera Slider, remote controlled via Bluetooth
  ☆31Updated 4 years ago
• ThingEngineer / Laser-XY-Scanner
  Low Cost DIY Laser XY Scanner, Cutter, or Engraver
  ☆41Updated 6 months ago
• drandrewthomas / ESP32_GRBL_CNC_Wireless_Pendant
  A wireless GRBL CNC pendant project based on the ESP32 micro-controller
  ☆52Updated 4 years ago
• euphy / polargraph_server_polarshield_esp32
  PolargraphSD firmware for ESP32-based machines with Polarshield v3.x
  ☆33Updated 4 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆46Updated 3 months ago