Alternatives and similar repositories for paste-extruder

Users that are interested in paste-extruder are comparing it to the libraries listed below

• PixiePlacer / PixiePlacer
  The PixiePlacer is a DIY Pick and Place Machine for SMD Components running OpenPnP.
  ☆126Updated last year
• photonfirmware / photon
  Open-Source firmware for pick and place feeders
  ☆67Updated 4 months ago
• microsmt / Microsmt-PNP-hardware
  All documents about making microsmt pnpboard
  ☆60Updated 2 weeks ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆155Updated last year
• kingoflolz / linear-actuator-hardware
  ☆65Updated 3 years ago
• opulo-inc / feeder
  Source for LumenPnP Feeders
  ☆160Updated 3 weeks ago
• BoltzRnD / SmartPrintCoreH7x
  STM32H7 based Robust and Open Source 3D Printer Mainboard
  ☆70Updated last month
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated 2 years ago
• SupaCoder / 0816-Lumen-SMT-Feeder-Remix
  0816 SMT Automatic Feeder modified to work with the OpuloPNP. Custom firmware written for an arduino nano with a servo sheild can run 12 …
  ☆15Updated 3 years ago
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆74Updated 5 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆55Updated 7 months ago
• zapta / ble_stepper_motor_analyzer
  A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
  ☆53Updated 2 years ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 8 months ago
• Andrew-Dickinson / photonic-etcher
  Generate exposure masks for Anycubic printers from PCB Gerbers
  ☆97Updated last year
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆35Updated 3 years ago
• intelligent-agent / Recore
  Repository for Recore single board 3D printer control card
  ☆44Updated last week
• wntrblm / jellyfish-and-starfish
  ☆108Updated 2 years ago
• VikOlliver / RepRapMicron
  μRepRap - A 3D printer project designed to work at the micron scale
  ☆112Updated last week
• markmaker / PushPullFeeder
  All 3d-Printed Tape&Reel Feeder
  ☆79Updated 11 months ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆37Updated 2 years ago
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆147Updated last week
• ploopyco / pnp-feeder
  An automated feeder for pick and place machines.
  ☆159Updated 5 years ago
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆84Updated 2 months ago
• zapta / simple_stepper_motor_analyzer
  A DYI stepper motor analyzer. This is a new design that is based on Raspberry Pi Pico and users a compact single PCB design. NOTE: The l…
  ☆154Updated 2 years ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆63Updated 2 years ago
• richardklingler / openpnp
  My pick and place machine controlled by the great OpenPNP software.
  ☆77Updated 4 years ago
• ghent360 / PrntrBoardV2
  32-bit 3D Printer controller board using STM32F407 and replaceable TMC2660/2209 stepper drivers.
  ☆43Updated 4 years ago
• BEEMB / Battery-Health-Monitor
  Battery Health Monitor A compact device for monitoring the State of Health (SoH) and State of Charge (SoC) of lithium batteries. It uses …
  ☆32Updated 7 months ago
• Devtronic-US / SmartPendant
  ☆28Updated 10 months ago
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆117Updated 3 years ago