Alternatives and similar repositories for QuickPID

Users that are interested in QuickPID are comparing it to the libraries listed below

• Dlloydev / sTune
  Open loop PID autotuner using a novel s-curve inflection point test method. Tuning parameters are determined in about ½Tau on a first-ord…
  ☆125Updated 2 years ago
• Dlloydev / QuickPID
  A fast PID controller with multiple options. Various Integral anti-windup, Proportional, Derivative and timer control modes.
  ☆246Updated 2 years ago
• PowerBroker2 / ArduPID
  PID library for Arduinos with greater accuracy than the legacy Arduino PID library
  ☆111Updated 10 months ago
• Stan-Reifel / FlexyStepper
  Stepper motor control library for Arduino supporting in motion changes
  ☆68Updated 2 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆80Updated 5 years ago
• tgolla / GCodeParser
  The GCode parser is designed to parse GCode in order that it can then be processed.
  ☆29Updated 3 years ago
• pkerspe / ESP-FlexyStepper
  This library is used to control one or more stepper motors from an ESP32 device. It is based on the FlexyStepper library by S.Reifel but …
  ☆176Updated last year
• remrc / Two-Axis-Reaction-Wheel-Stick
  ☆29Updated 3 years ago
• Seeed-Studio / Seeed_Arduino_AS5600
  The library comes with AS5600. Through this library, we can realize read the angles 、get magnetic from a magnet underneath the sensor.
  ☆122Updated last year
• makerbase-motor / MKS-SERVO42D-57D
  Makerbase MKS SERVO57D NEMA23 closed loop stepper motor Driver FOC quiet and efficient RS485 / CAN
  ☆67Updated last month
• grblHAL / Simulator
  grblHAL drivers for simulation (Linux and Windows)
  ☆38Updated this week
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆88Updated 5 months ago
• T-Kuhn / ESP32-MicroRobotArm
  Micro Robot Arm with ESP32 and 28BY-48 12V steppers
  ☆82Updated 6 years ago
• Stan-Reifel / SpeedyStepper
  Stepper motor control library for Arduino
  ☆94Updated last year
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆81Updated 5 months ago
• RobTillaart / TCA9548
  Arduino library for TCA9548 8 channel I2C multiplexer and compatibles.
  ☆35Updated 3 months ago
• waspinator / AccelStepper
  Fork of AccelStepper
  ☆202Updated last year
• RobTillaart / AS5600
  Arduino library for AS5600 and AS5600L magnetic rotation meter
  ☆173Updated 6 months ago
• Saur0o0n / PIDKiln
  Kiln PID controller based on Espressif Systems ESP32 chip board with Arduino IDE.
  ☆160Updated last year
• Neumi / tmc2209_devboard
  An Arduino shield to test the TMC2209 stepper motion controller by Trinamic.
  ☆37Updated 2 years ago
• MGX3D / EspDRO
  ESP32 DIY Digital Readout
  ☆110Updated 6 years ago
• ArminJo / PWMMotorControl
  Arduino library to control brushed DC motors by PWM. Uses optional attached encoders to drive fixed distances.
  ☆52Updated 8 months ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 11 months ago
• ZaneL / quaternion_sensor_3d_nodejs
  ☆36Updated 5 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆62Updated last month
• Dlloydev / ESP32-ESP32S2-AnalogWrite
  ESP32 PWM, Servo, Easing and Tone. Smart GPIO pin management and advanced control features.
  ☆120Updated 2 years ago
• SuperMakeSomething / diy-3d-scanner
  MATLAB/Arduino code for DIY 3D Scanner Project featured in Super Make Something Episode 8
  ☆40Updated 2 years ago
• grblHAL / ESP32
  grblHAL driver for ESP32
  ☆120Updated last week
• HamidSaffari / ADS123X
  An Arduino library to interface with TI ADS1232 and ADS1234 MultiChannel 24-bit ADC For Bridge Sensors.
  ☆37Updated 5 years ago
• jmosbacher / ClosedStepper
  Arduino library for closed loop control of a stepper motor with an encoder.
  ☆25Updated 6 years ago