MagnusThome / RejsaRubberTracLinks
RejsaRubberTrac - A wireless thermal camera for monitoring tire temperatures
☆165Updated last year
Alternatives and similar repositories for RejsaRubberTrac
Users that are interested in RejsaRubberTrac are comparing it to the libraries listed below
Sorting:
- ☆70Updated 2 years ago
- CAN Reverse engineering tool for ESP32 based boards (specifically EVTV ESP32Due)☆352Updated 3 weeks ago
- RealDash examples and technical materials☆173Updated 3 weeks ago
- Raspberry Pi / Teensy based Digital Gauge Cluster☆76Updated 2 years ago
- Hardware - CAN enabled small input / output expansion board. Switch panels, steering wheel buttons/knobs, etc.☆48Updated 2 months ago
- ☆156Updated 2 weeks ago
- DIY BLE device for RaceChrono, currently supports reading data from the CAN bus☆122Updated 9 months ago
- ESP32 based CAN development board☆183Updated 3 years ago
- Generalized Vehicle Reverse Engineering Tool - firmware for Arduino Due based boards☆107Updated 7 years ago
- CANbus shift light, works with Neopixels and MCP2515 to make a shiftlight that works over CAN.☆19Updated 11 months ago
- Hello world sample code for the ESP32-S3 dual CAN bus development board☆27Updated 6 months ago
- Kawasaki Diagnostic Service Reader via Bluetooth☆176Updated 2 years ago
- Can bus monitoring tool based on arduino and can bus shield. Implements CAN ASCII/SLCAN protocol compatible with Lawicel CAN232/CANUSB. C…☆329Updated 3 months ago
- The KWP2000 is a communications protocol used for on-board vehicle diagnostics systems (OBD) by Suzuki (SDS), Kawasaki (KDS), Yamaha (YDS…☆289Updated 3 years ago
- External information display for modern Honda motorcycles, using the HDS (diagnostic) connector on the ECU and other sensors (e.g GPS, DH…☆111Updated 2 years ago
- An Arduino sketch for controlling a Bosch LSU 4.9 Wideband Lambda sensor with minimal parts☆85Updated 12 years ago
- Arduino Uno + Seeed Studio CANBUS + BMW M57 diesel☆46Updated 4 years ago
- Arduino ODBII ELM327 Emulator - Allows Arduino to act as an OBD2 ELM327 device and responde to PID requests☆69Updated 2 years ago
- Dash display project for Megasquirt ECUs based on ESP32 and EVE2☆35Updated 6 years ago
- BMW CANBUS/DBUS/IBUS/KBUS information/reference/examples☆68Updated 7 years ago
- Wideband Lambda Controller with Bosch CJ125☆45Updated 2 years ago
- Speeduino compatible engine control unit (ECU) based around black STM32F407VET6 board.☆52Updated 2 years ago
- Arduino/Teensy CAN Gauges with OLED displays☆17Updated 7 years ago
- Collections of Arduino codes that reads and translates Honda OBD codes to ELM / OBD 2 PID codes. It also process and displays the output …☆172Updated last year
- 8Ch EGT sensor board to be used with aftermarket ECUs☆35Updated last year
- Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are availabl…☆99Updated 2 weeks ago
- This repo for using your Arduino with MCP2515 CAN Interface and CANHacker software☆59Updated 4 years ago
- File converter from DBC to RealDash XML☆18Updated 9 months ago
- Arduino Due solution for adding vin-coded modules to BMW cars☆66Updated 7 years ago
- ESP32 and ESP32-S3 board with CAN interface, runs on 12V power (with auto shutdown)☆717Updated 2 months ago