Alternatives and similar repositories for SmartPrintCoreH7x

Users that are interested in SmartPrintCoreH7x are comparing it to the libraries listed below

• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated 2 years ago
• zapta / ble_stepper_motor_analyzer
  A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
  ☆53Updated 2 years ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆97Updated 3 months ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆54Updated 7 months ago
• Rack-Robotics / Powercore-V1.0-Hardware
  CAD & Electronics for Powercore V1
  ☆157Updated last year
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆56Updated last week
• zapta / simple_stepper_motor_analyzer
  A DYI stepper motor analyzer. This is a new design that is based on Raspberry Pi Pico and users a compact single PCB design. NOTE: The l…
  ☆153Updated 2 years ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆162Updated 3 months ago
• markniu / PandaCAN
  CAN bus extruder, more resistant to noise,reduce a lot of wires for your 3D printer
  ☆115Updated 2 years ago
• marcoreps / linuxcnc_leadshine_EL8
  LinuxCNC configuration with EtherCAT Servo Drives Leadshine EL8 and some Beckhoff IO Modules
  ☆39Updated last year
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆62Updated 2 years ago
• Rack-Robotics / Powercore-V2.0
  Open-Source wire EDM power supply by Rack Robotics, Inc.
  ☆194Updated last year
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆90Updated 3 months ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆37Updated 2 years ago
• IvDm / Z-probe-on-smd-resistors-2512
  Auto bed level strain gage for 3D printer using resistors 2512 instead of strain gauges.
  ☆145Updated 5 years ago
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆66Updated 3 months ago
• prusa3d / Buddy-board-MINI-PCB
  ☆59Updated 2 years ago
• fractalrobotics / Fractal-Cortex
  A Multidirectional 5-Axis FDM Slicer
  ☆115Updated 3 months ago
• owhite / MP2-DFN
  A variant of the MP2 electronic speed control with DFNW MOSFETs
  ☆23Updated last year
• Rack-Robotics / Powercore-V1.0-Manual
  Theory and operation of the Powercore V1 EDM PSU
  ☆47Updated 2 years ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆154Updated last year
• Devtronic-US / SmartPendant
  ☆28Updated 9 months ago
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆83Updated last month
• opulo-inc / paste-extruder
  Paste extruder head for the LumenPnP
  ☆49Updated last month
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆74Updated 5 years ago
• nickshl / SmartPendant
  SmartPendant - a way to control grblHAL based CNC machine without PC
  ☆60Updated 2 months ago
• PixiePlacer / PixiePlacer
  The PixiePlacer is a DIY Pick and Place Machine for SMD Components running OpenPnP.
  ☆123Updated last year
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆116Updated 3 years ago
• ftobler / pick-plaz
  Open source pick and place machine
  ☆26Updated last year
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆146Updated last week