markniu / PandaZHULinks
3D printer control board based on ESP32,support 8 Driver motors.
☆88Updated 5 months ago
Alternatives and similar repositories for PandaZHU
Users that are interested in PandaZHU are comparing it to the libraries listed below
Sorting:
- Alternative to PanelDue. Embedded UI for Duet & RepRap based 3D printers. Running on the ESP32. Optimized for 3.5" displays. WiFi or UART…☆89Updated 3 years ago
- FYSETC Board - The E4 board is a minimal 3D printer control board based on the ESP32 microcontroller from ESPRESSIF, with built-in Wi-Fi …☆73Updated 10 months ago
- A powerful 32-bit 3D printer control board.☆74Updated 5 years ago
- MRR ESPE 3D printer control board☆38Updated 6 years ago
- ESP32-based 3D printer controller☆132Updated 4 years ago
- A basic 3D printer control board based on ESP32☆58Updated 6 years ago
- Include MKS TMC2209, MKS TMC2225, MKS TMC2208, MKS TB67S109 and so on☆72Updated 2 years ago
- A Grbl_ESP32CNC Controller for MPCNC☆90Updated 3 years ago
- A CNC Pendant on ESP32 board, with LCD, WiFi and SD card☆81Updated 5 months ago
- MKS TinyBee is a mainboard for 3d printing, based on ESP32 module☆166Updated 3 years ago
- grblHAL driver for ESP32☆120Updated this week
- An Arduino Shield for 3D printers☆41Updated 6 years ago
- Inculde MKS TFT24/28/32/35/70； MKS TS35/TS35-E3 Hardware☆62Updated 2 years ago
- List of controllers supported by grblHAL☆61Updated last month
- The TMC5160 contains the complete intelligence which is required to drive a motor. Receiving target positions the TMC5160 manages motor m…☆68Updated 6 years ago
- grbl controller for esp32☆203Updated 2 years ago
- A Pendant for FluidNC CNC Firmware☆81Updated 3 weeks ago
- SmartPendant - a way to control grblHAL based CNC machine without PC☆67Updated last month
- The closed-loop drive is to feedback the rotation angle of the stepping motor to the control panel, compare the distance that needs to be…☆26Updated 6 years ago
- ESP3D library for Marlin and ESP32 boards☆115Updated last month
- The source code of MKS DLC32☆107Updated 2 years ago
- A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.☆55Updated 2 years ago
- The closed-loop drive is to feedback the rotation angle of the stepping motor to the control panel, compare the distance that needs to be…☆113Updated 4 years ago
- Auto bed level strain gage for 3D printer using resistors 2512 instead of strain gauges.☆148Updated 5 years ago
- A DYI stepper motor analyzer. This is a new design that is based on Raspberry Pi Pico and users a compact single PCB design. NOTE: The l…☆155Updated 2 years ago
- GRBL ported to ESP8266, using up to 8 axis. No arduino involved☆60Updated 8 months ago
- CAN bus extruder, more resistant to noise,reduce a lot of wires for your 3D printer☆116Updated 2 years ago
- A wireless GRBL CNC pendant project based on the ESP32 micro-controller☆54Updated 4 years ago
- 4 Axis CNC Controller for Grbl_ESP32☆69Updated 5 years ago
- MKS DLC support grbl firmware, can use Laser mode and CNC mode,support connect MKS TFT24/32/35 and TFT_CNC firmware support lasering and …☆107Updated 4 years ago