Alternatives and similar repositories for owslave

Users that are interested in owslave are comparing it to the libraries listed below

• wd5gnr / qrigol
  Qt assistant for Rigol DS1000 series scopes
  ☆134Updated 5 years ago
• jmwilson / ollie
  Voice control for digital oscilloscopes using Snips
  ☆42Updated 5 years ago
• casanovg / timonel
  ATtiny85/45/25 I2C bootloader
  ☆113Updated 2 years ago
• rfinnie / rdserialtool
  rdserialtool - RDTech UM/DPS/RD series device interface tool
  ☆99Updated 3 years ago
• hwstar / HW-AC-Emeter
  Hardware for an ESP8266 or Arduino based AC power meter using the Atmel 90E24 energy management chip
  ☆53Updated 10 years ago
• xorbit / LiFePO4wered-USB-OSHW
  LiFePO4wered/USB power module open source hardware design files
  ☆42Updated 6 months ago
• MarkusLange / OneWireSlave
  ☆40Updated 10 years ago
• rheslip / PyDSA
  Spectrum Analyzer for the Rigol DS1000 series oscilloscopes
  ☆138Updated 4 years ago
• dasaki / nanoReflowController
  Reflow Oven Controller. See below for more information.
  ☆79Updated 5 years ago
• baruch / b3603
  Alternative firmware for the B3603
  ☆67Updated 7 years ago
• pcbwriter / pcbwriter
  ☆30Updated 11 years ago
• tinylabs / openfixture
  Open Source Hardware Test/Programming Fixture
  ☆115Updated 5 years ago
• septillion-git / QC2Control
  Set the voltage of a Quick Charge 2.0 source via the Arduino.
  ☆68Updated 8 years ago
• madworm / Youyue-858D-plus
  CODE: Custom firmware for Youyue 858D+ (ATmega168/328P)
  ☆170Updated 7 years ago
• rbuj / FreeRouting
  Printed Circuit Board Routing Software from FreeRouting.net
  ☆29Updated 6 years ago
• Petezah / roomba_wall_v2
  An AVR program for ATTiny85 to transmit a virtual wall signal for an iRobot Roomba
  ☆32Updated 4 years ago
• LordBlick / kicadPanelizer
  KiCAD PCB panelization helper
  ☆30Updated 3 years ago
• vinodstanur / qi_wireless_receiver_attiny13
  A Qi wireless power receiver using attiny13
  ☆57Updated 6 years ago
• pmonta / gerber2graphtec
  Cut SMT stencils from gerber files using a Graphtec cutter
  ☆109Updated 5 years ago
• wigman27 / Arduino-Programmable-Constant-Current-Power-Resistance-Load
  This is all of the code, datasheets and design files for my instructable
  ☆37Updated 9 years ago
• lhartmann / esp8266_reprap
  ESP8266-based I2S-output WS2812(B) Driver
  ☆51Updated 9 years ago
• arachnidlabs / reload-pro
  Schematics and code for the Re:load Pro
  ☆102Updated 8 years ago
• baoshi / ESP-Breakout
  Breadboard adapter for ESP-07 / ESP-12
  ☆60Updated 8 years ago
• sleemanj / pcb-test-pattern
  A test pattern for checking your Homebrew PCB efforts.
  ☆24Updated 11 years ago
• cpldcpu / CandleLEDhack
  Candle LED reverse engineering and emulation
  ☆75Updated 11 years ago
• cnlohr / ethertiny
  A firmware-only half-duplex 10Base-T implementation for AVRs
  ☆132Updated last year
• pfalcon / blutunode
  Autonomous wireless sensor/actuator node using bluetooth modules based on CSR BlueCore chipset. See wiki for more info.
  ☆154Updated 7 years ago
• tuxyme / metal-pi
  Raspberry PI bare metal
  ☆48Updated 11 years ago
• dqydj / PaperBack_EPaper_Display
  Internet Connected or Standard Input EPaper Display
  ☆82Updated 7 years ago
• lucysrausch / jlcsmt-kicad-converter
  Converts kicad .csv BOM files to JLCSMT compatible BOM format.
  ☆51Updated 6 years ago