Alternatives and similar repositories for niscan

Users that are interested in niscan are comparing it to the libraries listed below

• 49thdiver / EV-Projects
  Nissan Leaf based EV conversions
  ☆10Updated 3 years ago
• Alfaa123 / Volvo-CAN-Gauge
  Reverse engineering the Volvo VIDA protocol and CAN network to gather diagnostic information not available via OBD2 on Volvo cars.
  ☆111Updated 3 years ago
• collin80 / CRC_Nissan
  C# app that shows a simple way to calculate the CRC byte used by some canbus frames in Nissan Leafs
  ☆12Updated 10 years ago
• dalathegreat / Nissan-LEAF-PTC-heater-reverse-engineering
  Tips and tricks on repairing the fragile ZE0 LEAF PTC heater
  ☆11Updated 2 years ago
• DaveBlackH / NissanLeafBMS
  Arduino Code to query a Nissan Leaf BMS for Pack information.
  ☆10Updated 4 years ago
• alexandreblin / arduino-can-reader
  An Arduino sketch to read data from a CAN bus
  ☆96Updated 6 years ago
• dalathegreat / Nissan-Leaf-Bruteforce-Upgrade
  Software for correcting instrumentation on a battery "bruteforce" upgraded LEAF
  ☆22Updated 4 years ago
• omarKmekkawy / Arduino_CANHacker
  This repo for using your Arduino with MCP2515 CAN Interface and CANHacker software
  ☆53Updated 4 years ago
• atc1441 / arduino-mcp2515
  Arduino MCP2515 CAN interface library
  ☆39Updated 5 years ago
• smartgauges / canbox
  Firmware for canbus boxes
  ☆96Updated last year
• mck1117 / proteus
  ☆40Updated 3 weeks ago
• pazi88 / 8Ch-EGT
  8Ch EGT sensor board to be used with aftermarket ECUs
  ☆32Updated last year
• Pytrex / NissanDefinitions
  Nissan and Infiniti ECU ROM Definition files for use with RomRaider Editor.
  ☆34Updated last year
• macchina / m2-hardware
  Designs for the Macchina M2
  ☆93Updated 4 years ago
• collin80 / GVRET
  Generalized Vehicle Reverse Engineering Tool - firmware for Arduino Due based boards
  ☆102Updated 6 years ago
• hackingvolvo / SardineCAN-Arduino
  Arduino firmware for Sardine CAN (Open Source J2534 device)
  ☆83Updated 10 years ago
• Autohome2 / dxControl-Gears
  ☆22Updated 7 years ago
• laszlodaniel / ChryslerScanner
  Hardware and software for interfacing Chrysler's legacy CCD/PCI/SCI-bus.
  ☆64Updated last week
• darkspr1te / elm327_clone
  ELM327 firmware for pic18f25k80 chip from china clone OBD2 diag boxes
  ☆40Updated 7 years ago
• jackm / carhack
  Reverse engineering vehicle CAN bus messages
  ☆27Updated 7 years ago
• turboat / eepromtool
  ☆49Updated 2 years ago
• rnd-ash / ultimate_nag52
  An open source TCM for Daimlers 722.6 gearbox. Resource repository
  ☆115Updated 9 months ago
• kkuchera / canalyze-hw
  Hardware for a CAN to USB bridge.
  ☆57Updated 6 years ago
• DaveBlackH / MazdaRX8Arduino
  This code runs on an Arduino device, and is designed to run as a replacement for the ECU in a Mazda Mark 1 RX8. There are many variation…
  ☆51Updated 4 years ago
• NefMoto / NefMotoOpenSource
  Open source collaborative projects driven by the NefMoto.com community
  ☆93Updated 7 months ago
• Isaac96 / EV-Code
  Arduino projects for the Boxster
  ☆20Updated 4 years ago
• HeinrichG-V12 / E65_ReverseEngineering
  ☆42Updated 3 years ago
• I-CAN-hack / pq-flasher
  This repository conatains tools to reflash a PQ35 VW EPS, it also contains some useful libraries to deal with the TP 2.0 transport layer …
  ☆124Updated last year
• rnd-ash / m2-utd-passthru
  Passthru API (j2534) Driver for Macchina M2 Under the dash
  ☆24Updated 3 years ago
• thomastech / CAN2Cluster
  CAN-Bus Emulator for Controlling Automotive Dashboard Instrument Clusters
  ☆40Updated last year