Alternatives and similar repositories for iDryer

Users that are interested in iDryer are comparing it to the libraries listed below

• regnaDkciN / Filament-Scale
  3D Printer filament scale.
  ☆20Updated 3 years ago
• pavluchenkor / iDryerController
  ☆58Updated 5 months ago
• CODeRUS / klipper_config
  ☆28Updated last year
• willngton / 3DPrinterConfig
  My 3D Printers Configuration backup - Marlin and Klipper
  ☆48Updated 3 years ago
• CODeRUS / klipper_extras
  Extras
  ☆19Updated 3 months ago
• Sergey1560 / fb4s_howto
  Howto
  ☆80Updated 2 years ago
• oducceu / klipper_configs
  ☆39Updated last year
• evgs / kross-pi-hat
  RPI/OPI Hat board for FB Ghost6 and Reborn2 touchscreens
  ☆17Updated 9 months ago
• JayceeB1 / Klipper-Auto-Power-Off
  A Klipper module that automatically powers off your 3D printer
  ☆19Updated 10 months ago
• MirageC79 / FilamentDryer_Controller
  Arduino OLED Rlelay and DS18B20 to control heater element of a 3D printing Filament dryer.
  ☆43Updated 5 years ago
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆24Updated 4 months ago
• Arksine / STM32_HID_Bootloader
  Driverless USB HID bootloader and flashing tool for STM32F10X devices
  ☆28Updated 5 years ago
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• SasaKaranovic / DIY-Filament-Dryer
  DIY WiFi Filament dryer
  ☆173Updated last year
• orobardet / klipper_nano_expander
  Klipper Nano Expander, an Arduino Nano Shield to be used as an auxiliary Klipper MCU
  ☆35Updated 2 years ago
• silver-alx / sbc
  Popular SBC linux images
  ☆30Updated last year
• manu7irl / klipper-DWC2-installer
  to streamline the install or upgrade of KLIPPER & DWC2 front-end for it. With these 2 together no need to use octoprint. I run mine on or…
  ☆56Updated 5 years ago
• kemsky / creality-k1-max-xy-rails-mod
  Creality K1 Max XY Rails Mod
  ☆37Updated 3 weeks ago
• MintyTrebor / moonNode
  A set of node-red nodes to interface with the Moonraker API for Klipper
  ☆18Updated 5 months ago
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆47Updated 2 months ago
• bdring / FluidDial
  A Pendant for FluidNC CNC Firmware
  ☆80Updated 3 weeks ago
• SasaKaranovic / winfidel-sensor
  Wireless Inline Filament Diameter Estimator Low-cost Sensor
  ☆196Updated last month
• DerrickDarrell / Creality-K1-K1-Max
  ☆98Updated 11 months ago
• dasburninator / klipper_lcd_menu
  A custom menu system for LCD displays on klipper based printers.
  ☆20Updated 6 months ago
• AFUDIrk / CADDeck
  This is a combined joystick and touch panel display suitable for use with common CAD programs.
  ☆25Updated last year
• K1-Klipper / installer_script_k1_and_max
  ☆59Updated last year
• cryoz / K1_tenso_manual
  ☆41Updated last year
• jjgraphix / KlipperSettingsPlugin
  Ultimaker Cura plugin to enable various settings and features specific to Klipper firmware.
  ☆111Updated 2 years ago
• stas2z / orange-pi-images
  Prebuilt orange pi images for selected boards with separate FAT boot partition
  ☆16Updated 2 years ago
• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆101Updated last month