Alternatives and similar repositories for iDryerController:

Users that are interested in iDryerController are comparing it to the libraries listed below

• CODeRUS / klipper_config
  ☆28Updated 9 months ago
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆97Updated 2 years ago
• Tombraider2006 / K1
  creality k1 klipper
  ☆88Updated last week
• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆97Updated last month
• dmitry-sorkin / BeMeGe
  BeMeGe extruder is BMG reverse, optimized for 3d printing
  ☆58Updated last year
• Sergey1560 / fb4s_howto
  Howto
  ☆77Updated last year
• silver-alx / sbc
  Popular SBC linux images
  ☆28Updated this week
• Sergey1560 / Marlin_FB4S
  Marlin 2.0 for Flying Bear 4S/5
  ☆225Updated 11 months ago
• dmitry-sorkin / K3D-VOSTOK
  K3D VOSTOK 3D printer
  ☆230Updated 2 years ago
• Chiffa-C3 / Shark-Extruder
  Экструдер разработанный для замены стандартного на принтере FBG6
  ☆24Updated last year
• dmitry-sorkin / k3d-minifeeder
  Miniature LGX Lite - compatible 3D printer feeder
  ☆26Updated 2 years ago
• cryoz / K1_tenso_manual
  ☆27Updated 7 months ago
• ArtificalSUN / MKS-WIFI_PS_uploader
  Simple G-code file uploader for 3D-printers equipped with MKS-WIFI module
  ☆55Updated last year
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆231Updated 2 years ago
• mvbasov / PETCTL
  Another variant of PET Pull (https://3deshnik.ru/forum/viewtopic.php?f=37&t=986) project controller
  ☆27Updated 2 years ago
• vladimir-poleh / klipper-config
  ☆10Updated last year
• dmitry-sorkin / k3d-accuracy-test
  FDM 3D Print accuracy test
  ☆29Updated 2 years ago
• willngton / 3DPrinterConfig
  My 3D Printers Configuration backup - Marlin and Klipper
  ☆44Updated 2 years ago
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆44Updated 2 years ago
• condottab / Roborock-CPAP
  CPAP cooling system using a Roborock fan
  ☆89Updated last year
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆19Updated last year
• PrintMakerLab / mks-wifi-plugin
  MKS wifi plugin for Cura
  ☆140Updated 10 months ago
• xreef / MKS_WIFI_upgrade_with_BeePrint_web_interface
  Firmware for MKS WiFi module from Makerbase with BeePrint Web Interface, tested with Flying Bear Ghost 4/5/6 Reborn Flsun
  ☆73Updated 3 months ago
• K1-Klipper / installer_script_k1_and_max
  ☆51Updated 7 months ago
• Vassssko / Voron-2.4-HV-electronic-compartment-mod
  Voron 2.4 clamps set to put many more things into the electronics compartment comparing to baseline.
  ☆19Updated 2 years ago
• evgs / kross-pi-hat
  RPI/OPI Hat board for FB Ghost6 and Reborn2 touchscreens
  ☆15Updated last year
• FB-G6 / Marlin
  Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin inst…
  ☆75Updated 7 months ago
• Roman-RV78 / Nalivator
  ☆22Updated 2 years ago
• fbeltrao-br / mksts35
  ☆68Updated last year
• CODeRUS / klipper_extras
  Extras
  ☆18Updated last year