Alternatives and similar repositories for ACRE

Users that are interested in ACRE are comparing it to the libraries listed below

• CrabLabsLLC / OpenMD
  ☆145Updated 11 months ago
• wagiminator / ADuM3160-USB-Isolator
  2.5kV USB 2.0 Isolator with 200mA Power Supply and Full Speed (12Mbps) Support
  ☆67Updated 3 years ago
• paulvee / 100MHz-Differential-Probe
  100 MHz Differential Probe V2
  ☆52Updated last year
• photonfirmware / photon
  Open-Source firmware for pick and place feeders
  ☆67Updated this week
• westonb / rogowski-relief
  rogowski coil current probe
  ☆201Updated 2 years ago
• timonsku / M.2-Card-Footprints
  Footprints and template for making your own M.2 devices
  ☆116Updated 2 months ago
• badgineer / MP2-ESC
  Multi-Platform, Modular, Powerful ESC
  ☆127Updated last year
• issus / DifferentialProbe
  Open Source 250MHz Differential Oscilloscope Probe
  ☆79Updated 3 years ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆73Updated last month
• jmwilson / oshw-active-probe
  2GHz single-ended active probe design
  ☆144Updated last year
• kingoflolz / linear-actuator-hardware
  ☆65Updated 3 years ago
• wntrblm / jellyfish-and-starfish
  ☆108Updated 2 years ago
• marcoreps / ADRmu
  ADR1000 10V standard
  ☆133Updated 5 months ago
• pgrady3 / EasyController3
  A simple BLDC motor controller, and the evolution of the EasyController2
  ☆92Updated last year
• VIPQualityPost / lemon-pepper-stepper
  simplefoc all-in-one 50W hybrid stepper + bldc driver
  ☆59Updated this week
• cooked / kimotor
  KiCad plugin for the design of parametric PCB motors
  ☆81Updated last year
• crteensy / FETProbe_tiny
  A tiny 1.3 GHz FET Probe
  ☆33Updated 3 years ago
• sensille / litehm2
  LinuxCNC FPGA board port to LiteX
  ☆31Updated 9 months ago
• jaromir-sukuba / J-SMU
  DIY source-measure unit
  ☆167Updated 3 years ago
• KoshiroRobot / FOC-Driver
  ☆87Updated 4 months ago
• microsmt / Microsmt-PNP-hardware
  All documents about making microsmt pnpboard
  ☆60Updated 2 weeks ago
• richardklingler / openpnp
  My pick and place machine controlled by the great OpenPNP software.
  ☆77Updated 4 years ago
• devbisme / WireIt
  KiCad PCBNEW plugin that lets you add wires between pads on a PCB, delete them, and swap wires between pads.
  ☆86Updated 8 months ago
• westonb / little-bee-B1
  A high performance current & magnetic field probe
  ☆282Updated 2 years ago
• Juanduino / STSPIN32G4-FunQi-Stack
  SimpleFoc Format Dev. for potential 8pin PWM stepper use w. 4th half-bridge (also 6pin PWM BLDC use w. extra FET driver for eg. brake-res…
  ☆12Updated 2 years ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆155Updated last year
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆80Updated last year
• blinken / power-rail-probe
  Low-noise oscilloscope power rail probe
  ☆87Updated 2 months ago
• eez-open / modular-psu-firmware
  Firmware for EEZ Bench Box 3 (BB3)
  ☆102Updated last year
• probe-scope / Probe-Scope-PCB
  Main Probe Scope PCB Repo
  ☆57Updated 6 years ago