Alternatives and similar repositories for anet-a8-upgrades

Users that are interested in anet-a8-upgrades are comparing it to the libraries listed below

• SkyNet3D / Marlin
  SkyNet3D's internal Marlin fork with Anet A8 / A6 hardware support.
  ☆133Updated 7 years ago
• SkyNet3D / anet-board
  This is a board definition which works in Arduino IDE 1.8.x for Anet Board targets.
  ☆206Updated 3 years ago
• Lauszus / Sanguino
  Sanguino add-on for the Arduino IDE, based on http://code.google.com/p/sanguino/
  ☆194Updated 2 years ago
• akaJes / marlin-config
  Marlin firmware instant configurator
  ☆393Updated 7 years ago
• ViperWorx / Drakon-Extruder
  3D Printable 3:1 Geared Extruder
  ☆82Updated 5 years ago
• vitormhenrique / OctoPrint-Enclosure
  OctoPrint Enclosure Plugin
  ☆401Updated 9 months ago
• ralf-e / ANET-3D-Board-V1.0
  Anet 3D Printer Board - Schematic and Board
  ☆122Updated 8 years ago
• Geeetech3D / Prusa_I3_3Dprinter
  Geeetech 3D printer (base on marlin)
  ☆90Updated 4 years ago
• Allted / Marlin
  Optimized firmware for RepRap 3D printers based on the Arduino platform.
  ☆79Updated 4 years ago
• BillyBlaze / OctoPrint-TouchUI
  A touch friendly interface for a small TFT module or phone
  ☆274Updated last year
• OctoPrint / OctoPrint-Slic3r
  Slic3r plugin for slicing within OctoPrint
  ☆96Updated 3 years ago
• eclsnowman / Eustathios-Spider-V2
  Update to Eustathios with a little bit of HercuLien Design Changes
  ☆110Updated 5 years ago
• kantlivelong / OctoPrint-PSUControl
  Smart control of your power supply via GPIO, GCODE Command, System Command, or variety of sub-plugins.
  ☆214Updated 2 years ago
• mjrice / wilson
  Reprap Wilson, 3D printer design
  ☆93Updated 10 years ago
• MarkWheadon / velocity-painting
  #VelocityPainting: patterning 3D prints by modulating the print speed
  ☆211Updated 8 years ago
• PrusaMK2Users / 3030_Haribo_Edition
  Aluminum extrusion conversion for the Original Prusa i3 MK2
  ☆202Updated 5 years ago
• Ultimaker / UltimakerOriginal
  BOM and parts for UM-original
  ☆99Updated 4 years ago
• skarab42 / RepRap-iTopie
  Prusa i3 Evolution
  ☆72Updated 4 years ago
• mcuadros / OctoPrint-TFT
  A OctoPrint touch interface for TFT touch modules based on GTK+3
  ☆174Updated 6 years ago
• derhopp / Marlin-with-Anycubic-i3-Mega-TFT
  Fork Marlin Firmware to support the Anycubic i3 Mega TFT
  ☆103Updated 7 years ago
• andrivet / ADVi3pp
  ADVi3++, an alternative and better firmware for Wanhao i3 Plus printers and clones. Fork of Marlin Firmware.
  ☆254Updated 7 months ago
• mmone / OctoprintKlipperPlugin
  A plugin for a better integration of Klipper into OctoPrint.
  ☆86Updated 5 years ago
• cabbagecreek / Marlin3DprinterTool
  Marlin3dPrinterTool is a open-source software that helps you configure and test your 3D printer.
  ☆266Updated 3 years ago
• sn4k3 / Ender3
  Supercharge your Ender3 with Guides, Mods and Addons
  ☆620Updated 3 years ago
• jeffeb3 / v1pi
  Preconfigured PI useful for users of the V1Engineering machines.
  ☆103Updated 4 years ago
• dc42 / OrmerodSensorBoard
  Z-height sensor board add-on for RepRapPro Ormerod 3D printer
  ☆105Updated 8 years ago
• TinkerGnome / Ultimaker2Marlin
  ☆110Updated 2 years ago
• cocktailyogi / EggDuino
  Arduino Firmware for Spherebot / Eggbot integration in Inkscape
  ☆95Updated last year
• trouch / CreawsomeMod
  Modification for Ultimaker Cura
  ☆497Updated 5 years ago
• probonopd / WirelessPrinting
  Print wirelessly from Cura, PrusaSlicer or Slic3r to your 3D printer connected to an ESP8266 or ESP32 module
  ☆376Updated 2 years ago