Alternatives and similar repositories for Marlin

Users that are interested in Marlin are comparing it to the libraries listed below

• mmone / marlintool
  A shell script for setting up a standalone Marlin build environment on Raspberry Pi and Linux in general.
  ☆34Updated 4 years ago
• kantlivelong / OctoPrint-PSUControl
  Smart control of your power supply via GPIO, GCODE Command, System Command, or variety of sub-plugins.
  ☆211Updated last year
• akaJes / marlin-config
  Marlin firmware instant configurator
  ☆389Updated 6 years ago
• SkyNet3D / anet-board
  This is a board definition which works in Arduino IDE 1.8.x for Anet Board targets.
  ☆206Updated 2 years ago
• OctoPrint / OctoPrint-Slic3r
  Slic3r plugin for slicing within OctoPrint
  ☆91Updated 2 years ago
• Lauszus / Sanguino
  Sanguino add-on for the Arduino IDE, based on http://code.google.com/p/sanguino/
  ☆191Updated last year
• vitormhenrique / OctoPrint-Enclosure
  OctoPrint Enclosure Plugin
  ☆399Updated last month
• derhopp / Marlin-with-Anycubic-i3-Mega-TFT
  Fork Marlin Firmware to support the Anycubic i3 Mega TFT
  ☆104Updated 6 years ago
• markwal / OctoPrint-GPX
  An OctoPrint plug-in to use GPX as the protocol layer underneath rather than replacing g-code to talk to s3g/x3g machines, for example, a…
  ☆103Updated last year
• PrusaOwners / OctoPrint-PrusaMeshMap
  This plugin performs a mesh bed leveling operation then returns the results as an easy to read heatmap.
  ☆133Updated 3 years ago
• cabbagecreek / Marlin3DprinterTool
  Marlin3dPrinterTool is a open-source software that helps you configure and test your 3D printer.
  ☆259Updated 2 years ago
• Allted / Marlin
  Optimized firmware for RepRap 3D printers based on the Arduino platform.
  ☆79Updated 3 years ago
• TinkerGnome / Ultimaker2Marlin
  ☆109Updated last year
• 3d-gussner / Prusa-Firmware
  Firmware for Original Prusa i3 3D printers MK3S, MK3, MK2.5S, MK2.5 by PrusaResearch.
  ☆31Updated 2 months ago
• kennethjiang / OctoPrint-Slicer
  A full-blown GUI-based slicer plugin for OctoPrint
  ☆101Updated 8 months ago
• PrusaMK2Users / MK2_Tips_and_Tricks
  ☆108Updated 8 years ago
• th3dstudio / TH3D-Unified-U1.R2
  Easy to use, well tuned firmware for 3D printers.
  ☆136Updated 3 years ago
• ralf-e / ANET-3D-Board-V1.0
  Anet 3D Printer Board - Schematic and Board
  ☆114Updated 7 years ago
• donovan6000 / M33-Fio
  The ultimate OctoPrint plugin
  ☆125Updated 5 years ago
• OctoPrint / OctoPrint-AutomaticShutdown
  Plugin for automatically shutting down the system after print is finished
  ☆18Updated 3 years ago
• mcuadros / OctoPrint-TFT
  A OctoPrint touch interface for TFT touch modules based on GTK+3
  ☆174Updated 5 years ago
• ViperWorx / Drakon-Extruder
  3D Printable 3:1 Geared Extruder
  ☆83Updated 5 years ago
• BillyBlaze / OctoPrint-TouchUI
  A touch friendly interface for a small TFT module or phone
  ☆276Updated last year
• fieldOfView / Cura-OctoPrintPlugin
  Cura plugin which enables printing directly to OctoPrint and monitoring the process
  ☆500Updated 2 years ago
• CarlosGS / grblForCyclone
  GRBL port for RAMPS and Sanguinololu boards. Original port was done by ArSi (read description)
  ☆85Updated 9 years ago
• Geeetech3D / Prusa_I3_3Dprinter
  Geeetech 3D printer (base on marlin)
  ☆86Updated 4 years ago
• cookiengineer / anet-a8-upgrades
  Anet A8 Upgrade Tutorial - A Step-By-Step Guide
  ☆135Updated 11 months ago
• MarkWheadon / velocity-painting
  #VelocityPainting: patterning 3D prints by modulating the print speed
  ☆209Updated 8 years ago
• jneilliii / OctoPrint-Tasmota
  ☆64Updated 2 months ago
• jonaslorander / OctoPiPanel
  OctoPiPanel creates a simple interface on a small screen to control OctoPrint.
  ☆80Updated 4 years ago