Alternatives and similar repositories for AutoDashFrontEnd

Users that are interested in AutoDashFrontEnd are comparing it to the libraries listed below

• Mathews2115 / AutoDashBackEnd
  Digital Dash 'backend' for Holley/Racepak CAN protocol
  ☆52Updated 11 months ago
• janimm / RealDash-extras
  RealDash examples and technical materials
  ☆140Updated 2 weeks ago
• joshellissh / PiDGC
  Raspberry Pi / Teensy based Digital Gauge Cluster
  ☆69Updated 2 years ago
• NMSTEC / Volvo_EPS_FREE
  ☆22Updated 2 years ago
• calvincestari / ecuExplorer
  An open-source application for the Subaru ECU.
  ☆34Updated 6 years ago
• joshellissh / pi-dgc
  Raspberry Pi based Digital Gauge Cluster
  ☆48Updated 2 years ago
• mantonakakis1 / MegaCAN
  Megasquirt CAN Protocol with Arduino
  ☆34Updated last year
• corygrant / CANBoard_HW
  Hardware - CAN enabled IO board
  ☆35Updated last month
• collin80 / GVRET
  Generalized Vehicle Reverse Engineering Tool - firmware for Arduino Due based boards
  ☆101Updated 6 years ago
• an-ven / VW-Instrument-Cluster-Controller
  Arduino and MCP2515 CAN bus VW Instrument Cluster Controller
  ☆40Updated last year
• kmalinich / node-bmw-ref
  BMW CANBUS/DBUS/IBUS/KBUS information/reference/examples
  ☆58Updated 6 years ago
• HeinrichG-V12 / E65_ReverseEngineering
  ☆41Updated 3 years ago
• TheJalpa / RasbpianMSDash
  A dash project for tunerstudio based on RASPBIAN
  ☆28Updated 4 months ago
• corygrant / dingoPDM
  ☆78Updated 2 weeks ago
• hyper-tuner / hypertuner-cloud
  The best way to share your FOME, Speeduino and rusEFI tunes and logs
  ☆64Updated last year
• seishuku / teensycanbusdisplay
  Jetta TDI aux display
  ☆18Updated 5 years ago
• ConnorRigby / rx8-ecu-dump
  utility to dump the Mazda RX8 (and maybe others) ECU firmware
  ☆31Updated 2 years ago
• DaveBlackH / MazdaRX8Arduino
  This code runs on an Arduino device, and is designed to run as a replacement for the ECU in a Mazda Mark 1 RX8. There are many variation…
  ☆51Updated 4 years ago
• Marcin648 / e90-dashboard-ets2
  ☆26Updated last year
• michaeldove / vagtuner
  Volkswagen Audi Group CANBus diagnostic and ECU firmware flashing
  ☆36Updated 8 years ago
• kostaszaf / can-gateway-sniffer
  An embedded CAN bus sniffer which is able to monitor any of the vehicle internal CAN bus and perform some action by triggering new CAN me…
  ☆66Updated 3 years ago
• NikolaKozina / j2534
  J2534 driver for linux
  ☆49Updated last year
• Autohome2 / dxControl-Gears
  ☆22Updated 7 years ago
• DeeEmm / DIY-Flow-Bench
  Volumetric flow bench based on ESP32 and MAF sensor.
  ☆31Updated 3 months ago
• MielArrojado / speeduino-ardugauge
  An OLED gauge for the Speeduino ECU. Uses UART (secondary serial) for communication.
  ☆37Updated 2 years ago
• tsharp42 / E46ClusterDriver
  An Arduino sketch and schematic for the hardware to drive a BMW instrument cluster over CAN-BUS, KBUS and general IO lines. The firmware …
  ☆35Updated 9 years ago
• merkur2k / MSCan_Gauge
  Megasquirt Gauge using CAN bus.
  ☆35Updated 3 years ago
• rnd-ash / j2534-arduino-win
  Windows code for J2534 Arduino
  ☆26Updated 4 years ago
• Autohome2 / speeduino
  ☆11Updated 3 months ago
• rnd-ash / ultimate_nag52
  An open source TCM for Daimlers 722.6 gearbox. Resource repository
  ☆113Updated 7 months ago