Alternatives and similar repositories for CC3D-CableCam-Controller

Users that are interested in CC3D-CableCam-Controller are comparing it to the libraries listed below

• Max-62 / nRF24L01-Frequency-Hopping-FHSS
  ☆100Updated 8 years ago
• AlkaMotors / f051bldc
  brushless motor control stm32f051
  ☆71Updated 4 years ago
• fishpepper / tinyPEPPER
  a tiny 16x16mm hole-to-hole 4in1 brushless ESC running BLHeli_s
  ☆73Updated 8 years ago
• schinken / PPMEncoder
  Generate a PPM Signal with an Arduino
  ☆65Updated 2 years ago
• ottoragam / Tarocco
  Closed Loop Motor Controller
  ☆135Updated 4 years ago
• olliw42 / uavcan4hobbyists
  STM32 32-bit microcontroller based UAVCAN nodes for DIY
  ☆80Updated 5 years ago
• soligen2010 / RC_RX_CABELL_V3_FHSS
  RC Reciever firmware using arduino and NRF24L01+
  ☆89Updated 4 years ago
• TechAUmNu / A200S
  A200S ESC - Based upon the VESC®*-Project
  ☆54Updated 7 years ago
• olliw42 / digaustracking
  360° gimbal target tracking system
  ☆14Updated 8 years ago
• LazemanCY / Ultimate-LRS
  My hardware design for 433MHz Ultimate LRS modules.
  ☆22Updated 6 years ago
• fishpepper / tinyOSD
  tiny OSD
  ☆45Updated 6 years ago
• DarrenLouw / SBUS
  Arduino library for the Futaba SBUS protocol
  ☆31Updated 7 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆79Updated 5 years ago
• ottoragam / Brushed-DC-Servo-Drive
  Low cost servo drive for small CNC machinery
  ☆54Updated 9 years ago
• kwikius / quantracker
  FPV antenna tracker based on a STM32F4 Discovery board and a pololu style servo motor
  ☆30Updated 6 years ago
• 3x8 / nostromo
  BLDC ESC firmware (GPLv3.0)
  ☆50Updated 5 years ago
• UncleRus / MultiOSD
  MinimOSD firmware for OpenPilot/LibrePilot CC/CC3D/Atom/Revolution/Revo Nano, MAVLink (APM/Pixhawk PX4/Paparazzi/generic MAVLink), GPS u-…
  ☆45Updated 8 years ago
• Dark-Guan / Ananas
  This is an Arduino based program for step motor controller,Ananas.
  ☆51Updated 8 years ago
• joewa / bldc-strip
  OpenBLDC Strip (STM32F103)
  ☆69Updated 8 years ago
• thomaspfeifer / PPM2USB
  AVR-based PPM to USB-Joystick Converter using V-USB
  ☆61Updated 12 years ago
• pitronicteam / FOC_ESC-hardware
  FOC_ESC hardware design repository
  ☆112Updated 6 years ago
• jakeread / tesc
  in-progress motor controller, towards accessible closed-loop control
  ☆14Updated 8 years ago
• ArcBotics / Servotor32
  Servotor32 - Open-Source, Low-Cost USB 32 Servo Controller
  ☆39Updated 9 years ago
• bitboxelectronics / R2C2_Firmware
  R2C2 -- electronics for RepRap 3D printers (and others), CNC and other machines.
  ☆36Updated 5 years ago
• omuzychko / StepperHub
  3-axis UART Stepper Hub for 20$ (STM32 Nucleo 64 & Arduino CNC Shield)
  ☆77Updated 9 years ago
• PlayUAV / PlayuavOSD
  A Graphical OSD for FPV
  ☆70Updated 9 years ago
• dungjk / grbl-stm32
  An open source, embedded, high performance g-code-parser and CNC milling controller. This is a port of GRBL 1.1 to STM32F10X target.
  ☆86Updated 3 years ago
• paparazzi / ppm-encoder
  PPM Encoder board http://paparazzi.enac.fr/wiki/ATmega_PPM_Encoder_Board
  ☆31Updated 13 years ago
• tmrttmrt / opentx
  OpenTX custom firmware for Transmitters
  ☆55Updated 5 years ago
• msglazer / Anti-Spark_Switch
  personal improvements/changes to the vedder antispark switch
  ☆67Updated 7 years ago