Alternatives and similar repositories for Kobra3-Firmware:

Users that are interested in Kobra3-Firmware are comparing it to the libraries listed below

• ANYCUBIC-3D / Kobra3
  ☆45Updated 6 months ago
• printers-for-people / ACEResearch
  Anycubic ACE Pro Reverse Engineering
  ☆29Updated 2 months ago
• utkabobr / DuckPro-Kobra3
  CFW for Anycubic Kobra 3
  ☆127Updated last month
• Bushmills / Anycubic-Kobra-3-rooted
  While the Kobra 3 is a nice printer, mechanically, its software support currently leaves much to desire. Here is a description how to set…
  ☆24Updated 5 months ago
• utkabobr / DuckACE
  ☆35Updated last month
• DnG-Crafts / ACE-RFID
  Anycubic ACE RFID Programming
  ☆28Updated this week
• CrealityOfficial / Creality_Sonic_Pad_Firmware
  Sonic Pad Firmware Burning Tutorial
  ☆65Updated last year
• rootiest / printcfg
  A suite of macros to enhance the klipper experience
  ☆104Updated last month
• jbatonnet / Rinkhals
  Custom firmware for the Anycubic Kobra series of 3D printers (Kobra 2 Pro, Kobra 3 and Kobra S1)
  ☆193Updated this week
• mainsail-crew / mainsail-config
  Mainsail klipper macros and settings
  ☆99Updated 5 months ago
• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆85Updated last year
• bofh69 / spoolman2slicer
  Spoolman to slicer filament transfer
  ☆49Updated last week
• Gliptopolis / WLED_Klipper
  A simple How-To for integrating LEDs with your Klipper/Moonraker machine
  ☆92Updated 2 years ago
• tinntbg / auto-power-off-klipper
  Auto power off setup for a Klipper printer
  ☆110Updated 3 weeks ago
• krautech / btt-eddy-guide
  A how-to guide on how to install BigTreeTech Eddy Probe
  ☆52Updated 8 months ago
• Low-Frequency / Klipper-Git-Backup
  Fully automated klipper backups
  ☆127Updated 7 months ago
• mainsail-crew / sonar
  Sonar is a small Keepalive daemon for MainsailOS.
  ☆90Updated 2 weeks ago
• bigtreetech / KNOMI
  ☆229Updated last month
• bigtreetech / Eddy
  ☆214Updated 4 months ago
• kevinakasam / FrankEnstein-Duct
  Frankenstein also known as Frank Enstein is a light weight fanduct for the Ender 3 or similar printers. It adds a 5015 blower fan and is …
  ☆101Updated 2 weeks ago
• Clon1998 / mobileraker_companion
  Companion for mobileraker, enabling push notification.
  ☆239Updated 4 months ago
• jjgraphix / KlipperSettingsPlugin
  Ultimaker Cura plugin to enable various settings and features specific to Klipper firmware.
  ☆109Updated 2 years ago
• vvuk / eddy-ng
  ☆96Updated last week
• KoenVanduffel / CR-6_Klipper
  A repository for Klipper firmware details for the Creality CR-6 printers.
  ☆99Updated last year
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆32Updated last year
• pavluchenkor / iDryer-Unit
  ☆75Updated 2 weeks ago
• 92jackson / mainsail-advanced-filament-swap
  Adds a GUI to filament changes and filament runouts for Klipper systems running Mainsail.
  ☆56Updated last year
• bigtreetech / ADXL345
  ☆65Updated 10 months ago
• D3vil-Design / K1-Hardware-Mods
  D3vil Design's K1 and K1 Max Hardware Modifications
  ☆211Updated last year
• YGK3D / Troodon-2-Klipper
  This is a Klipper configuration for the Troodon 2.0.
  ☆17Updated last year